SIOUX SC1PA Anleitungen

INSTRUCTIONS FOR SC1PA & SC3PA PNEUMATIC SCALERS
Read and understand these instructions before operating this tool.
Everyone using, maintaining, changing accessories or working near this tool must read, understand and follow these Safety Instructions!
INTENDED USE
The intended use of this tool is for cleaning and paint stripping on metal or roughing cement surfaces. Do not use this tool for any other purpose.
AIR SUPPLY
The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of an in-line filter and pressure regulator will insure
maximum output and tool life. Before connecting the tool, blow out the air line to remove water and dirt which may have accumulated.
LUBRICATION
An airline lubricator, set to deliver one drop per minute, is recommended. If a lubricator is not used, add .04 oz (1.2 cc) of Sioux No. 288 air motor oil into
the inlet daily.
HOSE AND HOSE CONNECTIONS
The supply hose I.D. should not be less than 3/8" (9.5mm). Do not use coupling or fitting with a smaller I.D. than the supply hose. When using quick
couplers, install a leader hose between the tool and the quick coupler.
GENERAL OPERATION
Operation
Tools are operated with a lever throttle. Be sure the pistons are against the work piece before depressing the lever. Release the lever to stop the tool.
Pistons are replaced by removing the internal retaining ring from the tool body and tapping the piston to drive out the ring seal and plug. Assemble in
reverse order and be certain that the retaining ring locks properly into the groove.
Never operate the scaler without a chisel because internal damage can occur to the tool.
Always unhook tool from the air supply before changing pistons.
IF THE TOOL LOSES POWER, CHECK THE FOLLOWING:
• Air pressure
Ensure that there is adequate supply of clean, dry air at 90 psig (6.2 bar).
• Piston
Check for worn and broken pistons.
• Hose size
Ensure that the hoses, couplers, and fittings meet the criteria in "HOSE AND HOSE CONNECTIONS".
• Sluggish or erratic operation
Flush tool out with a small amount of petroleum solvent and operate for a few seconds, then re-lubricate the tool using air motor oil. If the tool still does
not perform correctly it will need to be disassembled and repaired.
Catalog No.
SC1PA
SC1PA-C
SC3PA
SC3PA-C
We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products
to which this declaration relates are in conformity with the following standard or standards or other normative document or documents:
Murphy, North Carolina, USA
Date and place of issues
250 Snap-on Drive • PO Box 1596 • Murphy, NC 28906 • USA • Phone: 828-835-9765 •www.siouxtools.com
Form ZCE681
SAVE THESE INSTRUCTIONS!
When used improperly power tools can create hazardous situations.
Improperly used power tools can cause injury or death.
SOUND AND VIBRATION READINGS
*Sound Pressure dBA
94.8
94.8
96.9
96.9
*per PN8NTC1
DECLARATION OF CONFORMITY
SC1PA, SC1PA-C, SC3PA, SC3PA-C
EN 792 (draft), EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1
following the provisions of
89/392/EEC as amended by 91/368/EEC & 93/44/EC Directives.
July 1, 2003
Name and position of issuer
Original
Instructions
WARNING
*Sound Power dBA
106.4
106.4
108.5
108.5
*per PN8NTC1
Gerald E. Seebeck
President
Sioux Tools Inc.
1
Form ZCE681
Date 2003July30/B
Page 1 of 8
*Vibration m/s
2
22.2
22.2
33.6
33.6
*per ISO 8662
Signature of issuer
Date 2003July30/B