Safety Advice; General Advice - Palram Snap & Grow Montageanleitung

IMPORTANT
Please read
these instructions carefully before you start to assemble
this greenhouse.
Please
carry
out the
steps
in
the order set out
in
these instructions.
Keep
these instructions
in
a
safe place
for future
reference.
»
Safety Advice
We
strongly recommend the
use
of work
gloves
during
assembly.
Do
not attempt to assemble the greenhouse
in
windy
or
wet conditions.
Do
not touch
overhead power cables with the aluminum profiles. Always wear
shoes and safety goggles when working with extruded aluminum. Dispose of
all
plastic bags safely
-
keep
them out of
reach
of
small
children.
The greenhouse
must be
positioned
and fixed on
a
flat level surface. Do not
lean
against or push
the greenhouse during construction.
Keep
children away from the assembly
area. Do not position your greenhouse
in an area
exposed to
excessive
wind.
Do
not attempt to
assemble this greenhouse if you
are
tired, have taken drugs
or alcohol or if you are prone to dizzy spells. If using
a
step ladder or power
tools ensure that you follow the manufacturers
safety advice. Hot items such
as
recently used grills,
blowtorches, should kept away from the greenhouse
walls.
We
recommend the greenhouse
is
bolted to
a
concrete
base or slabs (fix
hinges
are
not supplied). However, if you want to fix directly
in
to the concrete
ensure
there
are no
hidden
pipes or cables
in
the ground before inserting the
pegs.
»
Care &
Maintenance
When
your greenhouse
needs
to
be cleaned,
use a
mild detergent solution and
rinse
with
cold clean water.
DO NOT use
acetone, abrasive cleaners or other
special detergents to clean the clear panels.
For
replacement
parts
-
call
our
service line.
For
additional information please visit our web
site:
www.palramapplications.com
Tools &
Equipment
Tape measure
Work gloves
Plastic
or rubber mallet
Phillipshead screwdriver
Step
ladder
Scissors
Spirit
level
-
For base
alignment
Cloth
»
General Advice
This multi-part assembly
is
best achieved by two people. Allow at least half
a
day for the assembly
process.
Site selection instruction-choose
a
sunny level position away from overhanging
trees. If
you
are
fixing
your greenhouse directly to
a
solid concrete foundation
use
the
pre
drilled
holes in
the metal
base
supplied. The
component
parts should be checked and laid
out
close at hand. Keep all small parts
(screws etc.)
in a
bowl
so
they
do
not get
lost.
Sort the parts and check against the contents parts
list.
Carry out the assembly steps
in
the order set
out
in
the instructions.
The front of the greenhouse
is
the wall including the
door, and
the
back
is
the opposite wall.
After
assembly
fit the greenhouse to the
base using
connectors
no. 924 and
fit
the whole unit to
a
leveled final
You may use Silicon
lubricant
spray in
order to help you slide the profiles
on
the
connectors. Do
not
spray the Polycarbonate panels.
Use
the rubber malet if
necessary.
40
Notes (by steps)
...
Step
4: Profile 848
should
be placed on the left
hand
side
to
be
connected to profile 849. Profile
848
is
the one with the connector at the end.
Step
5: After connecting profiles 816 to each
other
clean the connection area using
a
cloth.
Place
the cover strip
on
the connection only when
it
is
clean and dry.
Press
the cover strip from one
side
of
the connection to the other
as
mentioned
in
picture
4.
Step
8: Profile 835 & 836 should
be
aligned and
connected according to the illustration
on page
8 a
& b.
plug
23
should
be
inserted to
each
connection while the two dots
on
the front of
the plug should
be
in
horizontal position for
easy
assembly.
Step
10:
Use
part
95 as
a
template
in
order
to measure the gap between posts
of
the
greenhouse wall and roof
area.
Step 11: Profile
841
should
be
placed
on
the
right
hand
side. Profile 840
should
be
placed
on
the left
hand
side
when viewed from the front.
Step
12: Slide the panel 566
till
the end
of
the
rail
and insert it into
it's
final position
as
shown
in
illustration
c
.
Step 19:
Be
careful to assemble the window
in
the position
as
shown on picture
20
a.
profile 809
should be placed while the vent
is
closed to cover
any gap. Ensure profile
809
is
fitted correctly
as
shown on picture
20
b.The lip on 809 should
face
toward the gutter.
Step 22:
Slide
the panel
566
till
the end of the
rail
and insert it into
it's
final position
as
shown
in
illustartion
a
and
b.
Step 23: Step inside the greenhouse and turn
all 23
plugs
a
1/4
of
a
turn
clockwise.
Step 24:
Profiles 814
should
be
inserted from
the four corners of the greenhouse, then insert
profile
815
in
between them.
Step 25:
Ensure you use
long screw 450
to
secure
the door
catch 363
as
shown
in
illustration
b.
!
Important Recommendations
Firmly connect the greenhouse to
a
level
surface immediately after completion of
the assembly.
Anchoring this product to the ground
is
essential to
its
stability and rigidity.
It
is
required to complete this stage
in
order for your warranty to
be valid.
Tighten all screws once assembly
is
completed.