TA M2 series Gebrauchsanweisungen Seite 7

1 Attention: before any kind of installation read carefully this manual
2 Make sure your operator properly complies with the installation
requirements.
3 Furthermore:
·Your gate must perfectly slide (sliding wheels properly greased)
·Your gate must be equipped with opening and closing mechanical
devices.
·Your gate must comply with the current regulations.
Junctions:
· All junctions must be made without electricity.
· Do not forget to place an omnipolar breaking device close to the control
board (at least 3 mm distance among the junctions).
· Use a 6A automatic switch to preserve constantly the power supply.
Our use a single-phase 16A switch provided with fuses.
· Keep the accessory lines separated from the motor and control board
power supply lines, to prevent any installation misworking.
· Any control and safety outfits connected to the control board must be
tension free.
Spare parts:
Use only original spare parts.Dispose the batteries with the industrial
waste (Regulation no. 475/88).
Installation:
See the enclosed appendix "Generals" to prevent any improper use as
well as damages to persons, animals and properties.The use of this
equipment must comply with the safety criteria in force in the country it is
installed, as well as the standards governing proper installation.
Warranty:
The warranty released by the manufacturer does not respond in case of
tampering, negligence, improper use, lightning, over voltage or use by
unqualified staff.
The warranty is void in case:
· The installation procedure does not comply with the instructions reported
in the manual. The use of even a single component not complying with the
law in force or not original spare parts not allowed by the manufacturer,
makes the warranty void.
· The manufacturer is not held responsible for damages caused by an
improper and unreasonable use.
INSTALLATION INSTRUCTIONS
1 Before installation make the risk assessment referring to "Generals"
enclosed in this manual. Fill in the technical table excluding all the risks
found. In case of pending risks provide for a security system.
2 Check the safety tips enclosed into "Safety Criteria".
3 Check and identify all the components.
4 Identify the fixing point of the motor.
5 Place and fix the motor.
6 Fix the chain and the rack.
7 Let the gate slide manually by releasing the motor
8 Place all the accessories.
9 Spread out the cables according to the "Operational table".
10 Make the connections both on the control board and accessories.
11 Code the radio receiver.
12 Code the control board.
13 Adjust the control board push (POWER).
14 Try some test manoeuvres.
15 Code the "working times".
In case of anomalies call the nearest assistance centre to you.
FIXING THE GEAR MOTOR
· Fix the plate P1 to the ground, respecting the criteria in fig. A.
· Fix the motor to plate P1 using bolts M10x60 provided.
· Screw two nuts M10 and two washers Ø10 on each bolt (fig. B).
· The first nut is used to fix the motor to the bolt.
· The second nut is used to fix the bolt and the motor to plate P1, as well as
the millimetric adjustment of the height.The fixing bolts lead to a vertical
adjustment of about 15 mm. It is highly recommended to place the bolt in
the middle of each fixing slot of the motor. It is highly recommended to fix
the motor keeping a distance from plate P1 of about 30 mm (fig. B). In this
way it will be possible, at the end of the installation, to adjust perfectly both
vertically and horizontally the motor.
For private households: Informa on on Disposal for Users of WEEE This symbol on the product(s) and / or accompanying documents means that used electrical and electronicequipment (WEEE) should not be mixed with general
household waste. For proper treatment, recovery and recycling, please take this product(s) to designated collec on points where it will be accepted free of charge. Alterna vely, in some countries, you may be able to return your
products to your local retailer upon purchase of an equivalent new product. Disposing of this product correctly will help save valuable resources and prevent any poten al nega ve effects on human health and the environment,
which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collec on point. Penal es may be applicable for incorrect disposal of this waste, in
accordance with you na onal legisla on. For professional users in the European Union If you wish to discard electrical and electronic equipment (EEE), please contact your dealer or supplier for further informa on. For disposal in
countries outside of the European Union This symbol is only valid in the European Union (EU). If you wish to discard this product please contact your local authori es ordealer and ask for the correct method of disposal.
T.A. Tecno Automazione s.r.l. - Via Vicinale snc - 03018 - Paliano - (FR) - Italy - Tel +39 0775 533677 - Fax +39 0775 533299 - info@tecnoautomazione.com - www.tecnoautomation.com - www.tecnoautomazione.com
SAFETY CRITERIA
INSTALLATION TIPS
ENGLISH
FIXING OF B117 RACK
B117 is a nylon gear rack with steel core, M4 module and 20x26mm
dimensions, in 0.50 cm bars.
To fix it to your gate, please follow the instructions:
1 Release the motor and open the gate fully.
2 Place the first rack piece on the motors' pinion, level it off horizontally and
then fix it to the gate using the screws and the washers supplied.
3 Move the gate forward for about 0.50 cm
4 Couple a second piece of rack to the first one and lay it on the pinion
(picture D).
Keep the rack perfectly levelled and fix the second piece to the gate.
5 Repeat steps 3 and 4 to cover all the gate length
6 Lower the gearmotor position about 1 or 2 mm by adjusting the bolts on
the ground fixing plate, to avoid the gate weight overloading on the motor
pinion.
7 Fix the limit switch brackets (opening and closing limit switches) at the to
ends of the rack with the fitting dowels (picture E).
8 Make sure that your gates has mechanical stops and adjust the limit
switch brackets to make the gate stop before reaching the mechanical
stops.
The chain must be fixed to the supporting frame of the gate through the
proper bolts and screws provided.
1 Fix the two supporting plates of the chain to both limbs of the gate, at
proper height (fig. I).
2 Screw a bolt on the first threaded crop.
Put the threaded crop in the first fixing plate. Make sure the fixing hole of
the chain is turned towards the motor.
3 Put the second bolt and tighten them both about half stroke.
4 Screw a bolt on the second threaded crop. Place a spring on it and put it
all in the hole of the second fixing plate. Make sure the fixing hole of the
chain is turned towards the motor.
5 Bring the chain and cut it at proper seize to fix it to the two holes of the
treaded crops.
6 Fix the chain to one of the threaded crops through the provided joint.
Release the motor through its proper release key. Put the chain between
the pinion and parallel pin of the guide of the motor. Pull the chain to catch
up the hole of the second threaded crop. Fix the chain to the second
threaded crop through the provided joint. Put the chain under tension
screwing the bolts of both plates. The right tension level of the chain is
obtained when levering on any point of it, the chain tightener spring is still
able to compress.
7 Make sure the distance between the chain and the parallel pin is enough
to prevent the loss of the chain from its guide, without impeding it to slide.
Adjust eventually the distance by shimming the plate itself.
8 Fix on the frame of the gate the proper slide strokes. The gate must not
knock against the mechanical stops. Adjust therefore the slide stokes so
that the cylinder (fig. G) of the micro limit switch hits the slide stroke just
before the gate closes completely.
RELEASE AND LOCK THE MOTOR (FIG. C)
Put the proper key through the release seat and turn anticlockwise to
release and, clockwise to lock the motor.
(fig. D/E/F)
FIXING THE CHAIN