Mounting Procedure - RAVAK ROSA Montageanleitung

GB
Installation of the ROSA bathtub with plastic front panel
Fig. 1
D
To assemble the bathtub with the panel, use all the parts in the basic bathtub mounting kit plus the panel
accessories included in the PANEL and PANELKIT kits.
When installing the bathtub, item
supplemented by the following instructions, apply in the full extent.

Mounting procedure

1. Turn the bathtub upside down and place the cardboard parts of the packaging together with Styrofoam on
the corners so that the rim of the bathtub and the raised headrest do not become damaged.
2. The bathtub with a panel has 3 metal supports. Bolt the threaded rods (
openings in the supports by the inclined side. Mount the threaded rod ( ) (length 450 mm) with the supporting
leg to the other end of the support ( ) (length 850 mm) below the bathtub seat. Permanently mount the
separate supporting legs with a screw 125 mm long before fastening the supports. ATTENTION! The metal
supports are universal and may have more openings. When attaching them to the bathtub, use only the 6 mm
openings by the reinforced bottom, the 12.5 mm openings for the supporting legs and the threaded rods
according to the figure.
3. Mount the panel holder ( 104 ) between two nuts (
tighten the nuts; allow some clearance for mounting and adjusting.
4. Place the completed supports on the reinforced bottom of the bathtub and bring them into position. The
800 and 850 mm supports are perpendicular to the longitudinal axis of the reinforced bottom; the supports'
distance from the siphon axis is according to the table:
Dimension
The third, 600 mm support goes from the center of the bathtub seat sideways towards the bathtub arch. All
supports are turned by two 12.5 mm openings towards the bathtub arch. Trace the position of the supports on
the bathtub bottom.
5. Using a water level or set squares, measure the exact distance between the axis of the outer opening in the
support and the bathtub contour and shift the support so that the center of the opening in the long threaded
rod ( 101 ) is 40 mm from the bathtub edge and that the panel holder (
outer bathtub edge.
6. Trace the contours of the 6 mm openings in the metal supports on the bottom of the bathtub. Put the
supports to one side and, using the enclosed drill bit, drill the 3 mm fastening holes. ATTENTION drill only
within the reinforced part of the bottom to a depth of 10 mm using a stop so that you don't damage the plastic
of the bottom of the bathtub.
7. Put the supports back and bolt them using the screws ( ) and (
under the support edges touching the bathtub.
8. Adjust the position of the threaded rod with the holder (
bathtub. Apply a sufficient amount of cement to the marked spot on the bathtub rim under the support (
Tighten the nuts ( 102 ) on the support applying a little pre-stress so that the upper edge of the bathtub does
not become deformed.
9. Adjust the height of the panel holder (
edge and it matches the shape of the outer outline. To stabilize the lower part of the panel, mount the holder
( 105 ) under the support as a prop using the washer (
10. Place the bathtub in its final location and using a water level, adjust it to a horizontal position.
ATTENTION: for a bathtub with a panel, measure the distance between the floor and the bathtub cut line as
567 mm.
11. Slide the panel into the holders on the bathtub and level it. Trace the panel contour on the floor and on the
sidewalls.
Check the functioning of the supports (
12. After removing the panel, adjust the position of the support (
supporting legs ( ) and ( 6 112 ) as well as the panel holders (
13. Trace the upper bathtub edge on the walls and bolt the clips for the bathtub rim ( ) according to the
bathtub installation manual, item 16.
14. To fasten the panel to the side walls, two holders (
right. Place the holder ( 107 ) on the panel contour at the selected spot. Move the panel holder downwards,
under the bathtub, by the thickness of the panel, i.e. 3 to 4 mm from the panel contour and trace the centers of
the oval mounting openings on the wall. Drill 8 mm holes at the marked centers, insert the dowels (
bolt the panel holders ( 107 ) using the screws (
on the wall. Fig. 3 .
15. Mount the drain set on the bathtub. For soundproofing, it is recommended to attach a plastic foam band of
approximately 10x6 mm (12x5 mm) on the bathtub sides adjacent to the wall.
16. Place the bathtub back in its final location and suspend it on the plastic clips according to the bathtub
installation manual. Insert the front panel (
openings (at the center of the perforated sheet) on the panel at the positions of the side holders (
17. Using a 3 mm drill bit, drill a hole through the panel and the perforated sheet. Be CAREFUL not to damage
the plastic panel with the drill chuck! Fasten the panel using the self drilling screw (
washer ( 52 ); press the plastic cap (
18. If necessary, it is possible to cement the joints between the panel and the tiles or possibly the horizontal
joints. After cementing the bathtub to the tiles, or after mounting the bathtub laths, it is recommended to fill the
bathtub with approximately 100 liters of water and leave it until the next day until the cement sets.
101 Threaded rod M 12x550 mm
102 M 12 nut
103 Threaded rod support no. 17
104 Panel holder no. 15
105 Panel holder no. 10
106 Washer, Ø 13
107 Panel holder no. 20, lateral
108 Dowel, Ø 8
109 Dowel screw, Ø 4x40
110 Self-tapping screw, Ø 3.5x13
111 Metal support, length 600 mm
112 Plastic supporting leg, M 12
113 Washer for the plastic supporting leg
114 Threaded rod, M 12 x 125
115 Self-tapping screw, 5.5x16
A CONSTRUCTIONAL READINESS of the bathtub manual and item ,
2
102 ) on the other end of the 3 threaded rods (
140x105 150x105
J 200 260
K 200 230
7
Fig. 1 .
104 ); trace the position of the support (
104 ) so that the panel, after sliding in, is just below the bathtub cut
106 ) and secure it with the nut (
105 ) in the lower part of the panel.
104 Fig. 2 ).
107 ) are used for the left bathtub edge and two for the
109 ). Mark the axes of the panel holders on the panel contour
51 ) into the holders and level it. Mark the centers of the fastening
53 ) on the bolt head. Fig. 3 .
MOUNTING KIT - PANEL KIT
52 Plastic washer, Ø 4
53 Plastic cap, Ø 4
101 ) (length 550 mm) to the outer
3
101
160x105
310
250
104 ) is approximately 3 mm from the
115 ). It is recommended to use cement
102 ).
105 ); check and secure the position of the
.
9
107
110 ) with the plastic
MOUNTING KIT - PANEL
3 pcs
51 ROSA p anel 140, (150), (160)
18 pcs
3 pcs
3 pcs
3 pcs
3 pcs
4 pcs
8 pcs
8 pcs
Fig. 2
4 pcs
pc
1
1 pc
1 pc
1 pc
4 pcs
4 pcs
102
4 pcs
B
101
1, 2
). Do not
5
6
Fig. 3
103 ) on the
Bathtub rim
103 ).
108, 109
108, 109
108 ), and
).
1 pc
40
SILICONE
103
104
51
102
106
105
107
110
51
53
52
107
110
53
52
Æ 5,5x16
115
114
111
112
113