General Inspection - T.O.M TS210L Bedienungsanleitung

Bevel cut
A bevel cut is made by cutting across the grain of the workpiece with the blade angled to the fence and mitre table. the mitre table is set at
the zero degree position and the blade set at an angle between 0º and 45º (fig. Z).
1. Pull on the release knob (2) and lift the saw arm to its full height.
2. loosen the mitre locks (15).
3. Rotate the mitre table (12) until the pointer aligns with zero on the mitre scale (13).
4. Retighten the mitre locks (15).
WarninG. Be sure to tighten the mitre locks before making a cut. Failure to do so could result in the table moving during the cut, causing
serious personal injury.
5. loosen the bevel lock (7) and move the saw arm (1) to the left to the desired bevel angle (between 0º and 45º). tighten the bevel lock (7).
6. Place the workpiece flat on the table with one edge securely against the fence (11). If the board is warped, place the convex side against
the fence. If the concave side is placed against the fence, the board could break and jam the blade.
7. when cutting long pieces of timber, support the opposite end of the timber with side support bars, a roller stand or a work surface that is
level with the saw table.
8. Before turning on the saw, perform a dry run of the cutting operation to check that there are no problems.
9. Hold the operating handle (3) firmly and squeeze the switch trigger (16). Allow the blade to reach maximum speed.
10. Press the release latch (17) and slowly lower the blade into and through the workpiece.
11. Release the switch trigger (16) and allow the saw blade to stop rotating before raising the blade out of the workpiece. wait until the blade
stops before removing the workpiece.
Compound mitre cut
A compound mitre cut involves using a mitre angle and a bevel angle at the same time. It is used in making picture frames, to cut mouldings,
making boxes with sloping sides and for roof framing. Always make a test cut on a piece of scrap wood before cutting into the good material
(fig. a).
1. Pull on the release knob (2) and lift the saw arm to its full height.
2. loosen the mitre locks (15).
3. Rotate the mitre table (12) until the pointer aligns with the desired angle on the mitre scale (13).
4. Retighten the mitre locks (15).
WarninG. Be sure to tighten the mitre lock before making a cut. Failure to do so could result in the table moving during the cut, causing
serious personal injury.
5. loosen the bevel lock (7) and move the saw arm (1) to the left to the desired bevel angle (between 0º and 45º). tighten the bevel lock (7).
6. Place the workpiece flat on the table with one edge securely against the fence (11). If the board is warped, place the convex side against
the fence. If the concave side is placed against the fence, the board could break and jam the blade.
7. when cutting long pieces of timber, support the opposite end of the timber with the side support bars,
a roller stand or a work surface that is level with the saw table.
8. Before turning on the saw, perform a dry run of the cutting operation to check that there are no problems.
9. Hold the operating handle (3) and firmly and squeeze the switch trigger (16). Allow the blade to reach maximum speed.
10. Press the release latch (17) and slowly lower the blade into and through the workpiece.
11. Release the switch trigger (16) and allow the saw blade to stop rotating before raising the blade out of the workpiece. wait until the blade
stops before removing the workpiece.
MainTEnanCE
WarninG. Always ensure that the tool is switched off and the plug is removed from the power point before making and adjustments or
maintenance procedures.
Power cord maintenance
If the supply cord needs replacing, the task must be carried out by the manufacturer, the manufacturer's
agent, or an authorised service centre in order to avoid
a safety hazard.
Cleaning
1. Keep the tool's air vents unclogged and clean at
all times.
2. Remove dust and dirt regularly.
cleaning is best done with a soft brush or a rag.
3. Re-lubricate all moving parts at regular intervals.
4. never use caustic agents to clean plastic parts.
CaUTiOn. do not use cleaning agents to clean the
plastic parts of the saw. A mild detergent on a damp
cloth is recommended.

General inspection

Regularly check that all the fixing screws are tight.
they may vibrate loose over time.
22