Unpacking - T.O.M TS210L Bedienungsanleitung

UnPaCKinG

Due to modern mass production techniques, it is unlikely that your Power Tool is faulty or that a part is missing. If you find anything wrong, do
not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury.
1. Remove all loose parts from the carton.
2. Remove the packing materials from around the saw.
3. using the operating handle (3) carefully lift the saw from the carton and place it on a level work surface.
4. the saw has been shipped with the saw arm locked in the down position. to release the saw arm, push down on the top of the saw arm,
pull on the release knob (2) (fig. A1), rotate it 45° and let go (fig. A2), slowly raise the saw arm.
Do not lift the saw whilst holding on to the guards. Use the operating handle (3).
WarninG
Transportation
lift the mitre saw only when the saw arm is locked in the down position, the saw is switched off and the plug is removed from the power point.
Only lift the saw by the operating handle (3) or outer castings. do not lift the saw using the guards.
Bench mounting
The saw base has holes in each corner to facilitate bench mounting (fig. B).
1. Place the saw on a level, horizontal bench or work table using bolts (not supplied) and fix the saw to the bench using 4 bolts.
2. If desired, you can mount the saw to a piece of 13mm or thicker plywood which can then be clamped to your work support or moved to
other job sites and re-clamped.
.
CaUTiOn
Make sure that the mounting surface is not warped as an uneven surface can cause binding and inaccurate sawing.
Release knob The release knob (2) is provided for holding the cutting head down whilst transporting or storing the mitre saw (fig. C). The saw
must never be used with the release knob locking the head down .
Mitre table locks
The mitre table locks (15) are used to lock the table at the desired mitre angle (fig. D).
the mitre saw cuts from 0° to 45° both left and right. to adjust the mitre angle loosen the mitre table locks and rotate the mitre table to the
desired position. the mitre table features positive click stops at 0°, 15°, 22.5°, 30° and 45° for quick setting of common mitre angles.
WarninG. Be sure to tighten the mitre table locks before making a cut. Failure to do so could result in the table moving during the cut and
cause serious personal injury.
Bevel lock
The bevel lock (7) is used to set the blade at the desired bevel angle (fig. E). The mitre saw bevel cuts from 0° to 45° to the left. To adjust the
bevel angle loosen the bevel lock and adjust the saw arm to the desired bevel angle.
WarninG. Be sure to tighten the bevel lock before making a cut. Failure to do so could result in the saw arm moving during the cut and
cause serious personal injury.
spindle lock button
The spindle lock button (18) prevents the blade in the saw from rotating (fig. F).Depress and hold the spindle lock button while installing,
changing, or removing the blade.
rotating lower
blade guard
The rotating lower blade guard (5) provides protection from both sides of the blade (fig. G). It retracts over the upper blade guard (4) as the
saw is lowered into the workpiece.
turning on and off
1. To turn the saw on depress and hold the on/off trigger switch (16) (fig. H).
2. to turn the saw off release the on/off trigger switch (16).
setting the table square with the blade
1. Make sure that the electrical plug is removed from the power point.
2. Push the saw arm (1) down to its lowest position and engage the release knob (2) to hold the
saw arm in the transport position.
3. loosen the mitre locks (15).
4. Rotate the table (12) until the pointer is positioned at 0º.
5. tighten the mitre locks (15).
6. loosen the bevel lock (7) and set the saw arm (1) at 0º bevel (the blade at 90º to the mitre table). tighten the bevel lock (7).
7. Place a set square against the table (12) and the flat part of the blade (fig. J).
note. Make sure that the square contacts the flat part of the saw blade, not the teeth.
8. Rotate the blade by hand and check the blade-to-table alignment at several points.
9. the edge of the set square and the saw blade should be parallel.
10. If the saw blade angles away from the set square, adjust as follows.
11. use an wrench or adjustable wrench to loosen the lock nut securing the 0° bevel adjustment screw (10). Also, loosen the bevel lock (7)
(fig. K).
20