Technical Data - Royal Rbc 41 Bedienungsanleitung

Anleitung_RBC_41_SPK1:_

4. Technical data

Engine type
2-stroke engine, air-cooled, chrome cylinder
Engine power (max.)
Displacement
Idle speed of engine
Max. engine speed
Scythe
Trimmer
Max. twin line speed
Scythe
Trimmer
Ignition
Drive
Weight (with empty tank)
Long handle length
Cutting circle diameter of line
Cutting circle diameter of blade
Cutting line length
Cutting line diameter:
Tank capacity
Spark plug
Champion RCJ6Y/LDL7T / L8RTF
Petrol consumption (in accordance with ISO 8893)
at max. engine power
Specific fuel consumption (in accordance
with ISO 8893) at max. engine power
Vibration a
hv
Idling speed (max.)
Idling speed (max.)
L sound pressure level
pA
Idling speed (max.)
In operation (max.)
L sound power level
WA
Idling speed (max.)
In operation (max.)
22.12.2008 14:01 Uhr Seite 19
5. Installation
5.1 Installing the long handle
Install the long handle as shown in Figures D1 – D3.
Do not tighten the screws until you have set the
perfect working position with the carrying strap. The
1.4 kW/1.9 hp
long handle should be aligned as shown in Figure A.
40.6 cc
2800 +/- 200 rpm 5.2 Fitting / Replacing the blade (Fig. E1 – E3)
When the machine is supplied the blade is ready-
fitted. Therefore we will first explain how to remove it.
9,000 rpm
Line up the hole in the carrier plate (Fig. E1/ Item
26) with the notch beneath it and lock the carrier
8,400 rpm
plate with the size 6 Allen key (Fig. E1/E2)
Remove the securing nut for the blade using the
6,750 rpm
supplied spark plug wrench (Fig. E2). Important:
Left-hand thread!
6,300 rpm
Remove the pressure plate cover (Fig. E3/Item
Electronic
26) and the pressure plate (Fig. E3/Item 27)
Centrifugal clutch
The blade (Fig. E3/Item 4) can now be removed.
To assemble, proceed in reverse order. Please
7.0 kg
note that the side of the pressure plate (Fig.
150 cm
E3/Item 26) with the recess must point towards
Ø 41 cm
the blade.
Ø 23 cm
5.3 Installing the cutting line guard hood
8.0 m
Important: The cutting line guard hood must be fitted
2.0 mm if you wish to work with the cutting line.
The guard hood for the cutting line must be installed
0.8 l
as shown in Figures F1 – F3.
NGK BPMR7A /
A blade (Fig. F6/ Item A) on the underside of the
guard hood automatically cuts the cutting line to the
optimum length. This is covered by a guard (Fig.
F6/Item B).
0.8 kg/h
Remove the guard before you start working and
replace it when you have finished working.
457 g/kWh
5.4 Fitting / Replacing the line spool
Line up the hole in the carrier plate with the notch
beneath it and lock the carrier plate with the size 6
6.8 m/s 2
Allen key (Fig. F4)
7.2 m/s 2
Secure the line spool on to the locating pin (Fig. F5).
Important: Left-hand thread!
To dismantle, proceed in reverse order.
84 dB (A)
104 dB (A)
5.5 Mounting the blade guard hood
Important: The cutting blade guard hood must be
fitted if you wish to work with the cutting blade. The
102 dB (A)
guard hood for the cutting blade must be installed as
114 dB (A)
shown in Figures F7 – F9.
GB
19