Contents English - Bosch BSA / SDL 4 Series Originalbetriebsanleitung

Contents English

1. Symbols used
1.1 In the documentation
1.1.1 Warning notices -
Structure and meaning
1.1.2 Symbols in this documentation
1.2 On the product
2. User information
2.1 Important notes
2.2 Safety instructions
2.3 Configuration
2.4 Other applicable documentation
3. Product description
3.1 Intended use
3.2 Measurement quantities
3.3 Measurement visualization (operation)
3.3.1 General information
3.3.2 Check of calibration and configuration 41
3.3.3 Main window
3.3.4 Switching between the two halves of
the window
3.3.5 Selection and actuation of control ele-
ment
3.3.6 Main menu
3.3.7 Tester selection zone
3.4 Main switch box
3.5 Electrical cabinet
4. Operation
4.1 Switching the BSA 43xx on and off
4.2 Starting software modules
4.3 Software module termination
4.4 Operating modes
4.5 Brake test sequence
4.6 Notes on operation
4.6.1 General information
4.6.2 Notes on brake testing
4.6.3 Notes on brake testing for four-wheel
drive vehicles
4.6.4 Notes on motorcycle brake testing
4.6.5 Notes on suspension tester
4.6.6 Notes on noise simulator
4.6.7 Notes on side slip tester
4.7 Selecting test routine
5. Manual mode (normal operation)
5.1 Mode activation and deactivation
5.2 Test sequences
5.2.1 Vehicles test routine
5.2.2 Motorcycle test routine
5.2.3 Suspension tester SDL 43x
5.2.4 Noise simulator SDL 435
5.2.5 Side slip tester SDL 410
Robert Bosch GmbH
5.3 Remote control options
5.3.1 Manual entry of weights
40 5.3.2 Storing measured values
40 5.3.3 Display repetition
5.3.4 Deleting stored values
40 5.3.5 Displaying total deceleration
40 5.3.6 Display switching
40 5.3.7 Print-out of measurement results
40 6. Automatic mode
40 6.1 Mode activation and deactivation
40 6.2 Test sequences
40 6.2.1 Brake dynamometer BSA 43xx / BSA
40 44xx
6.2.2 Suspension tester SDL 43x
41 6.2.3 Side slip tester SDL 410
41
41 7. Super automatic mode
41 7.1 Mode activation and deactivation
41 7.2 Test sequence
7.3 Brake test options
41 7.3.1 Repetition of sub-task (Clear Last)
7.3.2 Parking brake on front axle
42
8. All-wheel super automatic mode
42 8.1 Mode activation and deactivation
42 8.2 Test sequence
42
43 9. Fault procedure
43 9.1 General information
9.2 Acknowledgement of warnings
44 9.3 BNet Office and SDL 43xx
44 9.4 Brake dynamometer series BSA 43xx
44 9.4.1 Warnings
44 9.4.2 Faults
44 9.5 Side slip tester SDL 410
45 9.5.1 Warnings
45 9.5.2 Faults
45 9.6 Chassis tester SDL 43x
45 9.6.1 Warnings
9.6.2 Faults
46
46 10. Appendix
46 10.1 Setting the date and time
46 10.2 Calculation methods
46 10.2.1 Deceleration
46 10.2.2 Out-of-roundness
10.2.3 Road surface adhesion
48
48
i
48 These operating instructions describe standard test
48 procedures. These standard test procedures may
50 differ from country-specific test procedures
53
55
56
| BSA 43xx | 39 en
57
57
58
58
58
59
59
59
60
60
60
60
63
64
65
65
65
66
66
66
67
67
67
68
68
68
69
70
70
70
70
70
70
70
70
70
71
71
72
72
72
72
|
1 691 606 210 2015-07-29