Werbung
Verfügbare Sprachen
Verfügbare Sprachen
L
Quick Guide SATA & ATA Combo Raid-Controller
When using more than one hard disc with SATA & ATA Combo RAID controller, always ensure this is the
same type or design. Problems can occur when using different types of hard disc due to incompatibility.
Installing the software
Attention: When installing Windows 2000 or XP onto a hard disc which is connected to the SATA & ATA
Combo RAID controller, first copy all files into directory \driver\floppy disk of enclosed driver CD to an
empty disc in drive (A:\). Before copying, please note that any concealed files or system files have been
made visible. See operating system manual or online help for instructions on how to view such files.
During installation, you will see the message: "To install an SCSI/RAID driver from another company,
press F6...". Now press
F6. When prompted, press either
ENTER. "Ali SATA RAID controller ( Windows XP), Ali ATA RAID controller (Windows XP)" should
appear in the next window. Select the correct driver for your operating system. Press
The necessary drivers are now copied. Another window now appears displaying the driver for your
operating system. In order to ensure installation process is successful, a second driver is required:
press
Z or Y
place disc into drive and press
Ali ATA RAID controller (Windows XP)" should appear in the next window. Select the correct driver for
your operating system. Press
ENTER.
The necessary drivers are now copied. Another window appears displaying the driver for your opera-
ting system. Since a second driver is needed for succesful installation, press
into drive and then press
ENTER. "Ali SATA RAID controller ( Windows XP), Ali ATA RAID controller
(Windows XP)" should appear in the next window. Select the driver for your operating system. Press
ENTER. The appropriate drivers are now copied. You should now have selected two different drivers for
your operating system. Ensure both drivers that have been selected are for the same operating system
and that both SATA driver and ATA driver have been selected in each case.
Press
ENTER
to continue installation process and install operating system as described in instruc-
tion manual. Before restarting your system for the first time, remove disc from disc drive. Should you
receive the message "Unsuccessful logo test" during installation, click
process.
Installation on Windows XP:
After booting, the assistant for locating new hardware will appear. Select the option "Install software
from a list or particular source (for advanced users)".
a window appear with the question "Which action do you want Windows to perform?", choose the
option "Do not carry out any action" and click on
enter "D:\driver\PC\win_xp" (whereby D: indicates the initial of your CD drive) or click "Browse" and
select the folder specified above.
Continue
found" appears, click
Back
and check you have entered the details correctly. Should you now
receive the message "The software which has been installed for this hardware, ... has not passed the
Windows logo test which checks compatibility with Windows XP." click on "Continue installation". The
necessary files will now be copied from the CD. Click
ware should then restart in order to integrate the second port into the system. To complete RAID
controller installation process, continue as described above. After completing second installation stage,
enclosed CD should be removed from drive and system should be restarted.
Important instructions for Windows XP:
You can check whether controller was installed properly by selecting Start
Hardware
Device Manager (in some systems, you must click Switch to Classic View to see the
System icon). The following should now appear - without yellow exclamation marks:
SCSI and RAID controller
• Ali ATA/RAID controller
• Ali SATA/RAID controller
Z or Y
place disc into drive and press
ENTER.
ENTER. "Ali SATA RAID controller ( Windows XP),
Z or Y
place disc
Yes
to continue installation
Continue
insert enclosed driver CD. Should
Ok
Now select "Browse following source:" and
If the window "Software for following appliance not
Ready
.. The assistant for locating new hard-
Control Panel
-5-
Installation on Windows 2000:
After booting, the assistant for locating new hardware will appear.
"Search for a suitable driver for this device (recommended)" and insert enclosed CD.
Now select "Specify another location". In the next window, enter the location
"D:\driver\PC\win_2000"(you may have to substitute the letter of your CD drive for D:) or click Browse
and select the above folder.
now appears, click
receive a message saying Windows cannot locate a digital signature, click
are now copied from the CD. Click
The assistant for locating new hardware should then restart, in order to integrate the second port into
the system. To complete the RAID controller installation process, continue as described above. After CD
has been removed from drive, system must be restarted. On some systems a message may appear after
restarting, saying Windows cannot locate a digital signature for controller driver. Click
installation process for SATA & ATA RAID controller is now complete.
Important instructions for Windows 2000:
You can check whether controller was installed properly by selecting
Panel
System
exclamation marks:
SCSI and RAID controller
• ALi ATA/RAID controller
• ALi SATA/RAID controller
Installation on Windows 98SE/ME/2000:
While booting, the message "New hardware component found" should appear. The controller is
identified as a."PCI mass storage controller" The hardware assistant then opens and searches for new
drivers for "PCI RAID controller". Place enclosed driver CD into CD drive. After the message "What do
you want Windows to do?", select
Select "Specify location" and enter "D:\driver\PC\win98_me"(you may have to substitute the letter of
your CD drive for D:) or click Browse and select the above folder.
saying "Software for device not found" appears, click
correctly.
Continue
installs SATA & ATA RAID controller. The installation assistant should then appear again in order to
integrate the second port into the system. To complete the RAID controller installation process,
continue as described above. After the CD has been removed from the drive, the system must be
restarted. After the CD has been removed from the drive, the system must be restarted.
Important instructions for Windows 98SE/ME:
You can check whether the controller was installed properly by selecting
Panel
System
exclamation marks:
SCSI controller
• Ali ATA/RAID controller
• Ali SATA/RAID controller
Please Note:
System
If you would like to use the ATA & SATA RAID CONTROLLER with an operating system not listed above,
first check whether additional information is available in the service section of www.hama.de or
whether drivers for this product exist.
BIOS settings for RAID controller
Please Note: Incorrect settings and/or changing existing arrays can lead to loss of data.
OK
Continue
If a window saying "Software for device not found"
Back
and check you have entered the details correctly. Should you now
Ready
..
Hardware
Device Manager. The following should appear - without yellow
"Specify location of driver (advanced)" and then click
Back
. the necessary files are now copied from the CD
Hardware fi Device Manager. The following should appear - without yellow
Continue
Choose the option
Continue
Yes
the necessary files
Yes
The
Start
Settings
Control
Continue.
OK
Continue
If a window
and check you have entered details
Ready. Windows now
Start
Settings
Control
Werbung
