Technical Characteristics - Vitek VT 4023 BN Betriebsanweisung

4023.qxd 12.09.2005
ENGLISH
Make sure that the device that you are connecting to the
subwoofer is turned off. Set the subwoofer's volume level to
the very minimum before turning it on.
1. Connect the wires for the front left and right satellite
speakers, the center speaker, and the rear left and right
satellite speakers to the output jacks on the rear panel of
the subwoofer, which are marked FR, FL, CEN, RP, RL
(see figure 2).
2. Connect an audio cable to the corresponding jacks on
the connecting device (for example, a DVD player); and
the opposite end of the cable to the corresponding audio
input jacks on the rear panel of the subwoofer (see figure
2).
3. Connect the power cord to the electrical outlet and flip
the power switch, located on the rear panel of the sub
woofer, to the ON position. Turn on the input device con
nected to the subwoofer and use the volume control
knob to set the desired volume levels on the subwoofers
channels.
RESOLVING MALFUNCTIONS
1. No sound.
Make sure that all the connections are correct, and also
that all the audio cables are connected firmly.
2. Low frequency (bass) sound is missing.
Set the desired bass level.
3. Not all of the speakers work.
Check all the connections between the speakers and the
subwoofer or connect a different audio source.
PRECAUTIONARY MEASURES:
Attention: Please carefully read the points listed below to
ensure safe use of the device.
1. Read the instructions The safety instructions and oper
ating rules should be read before using the device.
2. Save the instructions Save the instructions for future
use.
3. Follow the operating rules All of the safety instructions
should be followed.
4. Warning symbols Heed the indications of all warning
symbols located on the device's panels or in these
instructions.
5. Power source The device should only be connected to
a power source with the characteristics indicated on the
rear panel of the device or in these instructions.
6. Protecting the power cord The power cord should be
laid out in such a way that it will not be damaged by
external items or its surroundings.
7. Water and moisture Do not use the device near reser
voirs of water (for example, bath tubs, sinks, etc).
8. Ventilation Install the device in a well ventilated room.
10:17 Page 4
Do not install the device on couches, beds or carpets
because the device's ventilation may be blocked.
9. The effects of heat Do not install the device near heat
sources (for example, radiators, kitchen stoves, etc).
10. Periods of non use if the device will not be used for a
long period of time, disconnect the power plug from the
electrical outlet.
11. The need for maintenance Utilize the services of quali
fied technicians if:
• The power cord is damaged; or
• The device body is damaged; or
• The device was subjected to rain; or
• The device is not functioning properly; or
• The device was subjected to shock.
12. Repair service The consumer should not attempt to
repair the device himself. Use only the services of a qual
ified technician.
13. Clean the device with a dry, soft clothe only.
14. Turn off the device during thunderstorms or when not in
use for a long period of time.

TECHNICAL CHARACTERISTICS

Power supply:
Output power:
Subwoofer speaker:
Satellite speakers:
Reproduction frequency band: 20 Hz 200 Hz (Subwoofer)
The technical characteristics of the device may be changed
without prior notice.
Service life – no less than 5 years.
Guarantee
Details regarding guarantee conditions can be obtained from
the dealer from whom the appliance was purchased. The bill
of sale or receipt must be produced when making any claim
under the terms of this guarantee.
This product conforms to the EMC Requirements as
laid down by the Council Directive 89/336/EEC and
to the Low Voltage Regulation (23/73 EEC)
4
~220 230 Volts
50 W (Subwoofer) + 5 x 20 W
(Satellite speakers)
6.5"/4 Om
3"/8 Om
150 Hz 20 KHz
(Satellite speakers)