Intended Use; Unpacking; Preparing Of The Blower Vac Prior To Use - Impos 2510 Gebrauchsanweisung

• Do not operate the tool near people, especially chil-
dren or pets. Turn it off if they get too close. Maintain
a safe distance of at least 5m from other people when
using the tool.
• Never direct the blower tube towards bystanders or
pets. Never blow debris in the direction of bystanders
or pets. The operator is responsible for accidents or
hazards occurring to other people or their property.
• Do not handle the plug or the tool with wet hands and
do not use the tool in the rain.
• Use only outdoor rated extension leads that are so
marked. Keep the extension cord away from heat, oil
and sharp edges.
• Ensure that the extension lead is secured in a manner
that prevents it form disconnecting from the plug whilst
in use.
• Keep all the air intakes and the blower tube free of
dust, lint, hair and other material that may cause a
reduction in air flow.
• Keep a balanced and stable stance while using the
tool.
• Do not switch on the tool in enclosed or poorly ven-
tilated spaces or in the presence of inflammable and
/or explosive substance such as liquids, gases and
powders.
• Do not get distracted and always concentrated on what
you are doing. Use common sense. Never operate the
tool when you are tired, sick or under the influence of
alcohol or other drugs.
• Do not operate this appliance with long loose hair or
loose fitting jewellery. Tie long loose hair back and
remove loose fitting jewellery.
• Do not allow the blower vac to pick up any burning or
smoldering materials like ashes, cigarette butts etc.
• Do not attempt to pick up breakable objects like glass,
plastics,china etc.
• Do not use in vacuum operation without the collection
bag fitted
• Do not use the blower vac in either the vacuum or the
blower position on gravel surfaces.
• Only operate the tool during broad daylight or with
adequate artificial light.
• When the tool is not in use, store it in a dry place and
out of reach of children.
• After use ,disconnect the tool from the power supply
and check for damage. If you have the slightest doubts
, contract an authorized service centre.
• Only use the tool according to the instructions given in
this manual.
• Check regularly that screws are tight.
• Use only spare parts and accessories recommended
by the manufacture.
• Do not try to repair the tool or access internal parts.
Contract authorized service centers only.

Intended use

The leaf vac is exclusively used in the two following
ways:
1. As a leaf vac for vacuuming up dry leaves.
2. As a blower it is used to collect together dry leaves or
to remove them from inaccessible places (e.g. under
vehicles).
In suction mode it also works as a shredder, where the
volume of the leaves is reduced by a ratio of approx.
10:1 and takes up less space in the leaf collection bag
and the collected material is simultaneously prepared for
possible composting.
Each type of use other than those given in these instruc-
tions for use can damage the machine and cause seri-
ous risk to the user.
Please always observe the safety instructions in order
to safeguard your guarantee claim and in the interests
of product safety. Due to the machine's design, we are
unable to fully exclude all residual risks.

Unpacking

Due to modern mass production techniques, it is unlikely
that your power tool is faulty or that a part is missing. If
you find anything wrong, do not operate the tool until the
parts have been replaced or the fault has been rectified.
Failure to do so could result in serious personal injury.

Preparing of the blower vac prior to use

The blower vacuum requires some assembly prior to use
for the first time This includes the fitting of the blow/vac
tube to the housing and the fitting of the collection bag.
Handle assembly
Support handle attached as shown on the images to
push up in the housing and plug it firmly into place.
Assemble the Tube and wheel bracket
1. Insert the lower tube to the upper tube and align the
screw hole in the upper tube with the screw hole in
the lower tube, at the same time the convex plate can
match the slot on upper tube firmly (fig. 3).
2. Locate one screw (A) (ST4.2x50) in big screw hole on
upper tube (fig. 5).
3. Tighten the screw securely and tortque to 1.2N.m
minimum.
4. Assemble the Wheel Bracket: Insert the wheel bracket
from the end Lower tube till it reach the rib position
and can not forward again (fig. 6).
5. Locate one screw (ST4.2x15) in the screw hole on
wheel bracket (fig. 7).
6. Tighten the screw firmly (fig. 8).
7. The ready-mounted suction - and blowpipe with strong
pressure to stop the import motor housing. (Fig. 8 a).
The tube with the supplied screw (ST 4.2 x 50) firmly
connected (Fig. 8 b)
Fitting the collection bag
1. Connect the strap(15) onto the hook (4) in the housing
(fig. 9)
2. Attach the push-on collection bag connector (8) to the
outlet tube of the housing. Push the fitting of the col-
lection bag directly onto the outlet until it "clicks" into
position (fig. 10).
3. Repeat the first step to connect the strp to the sen-
cond hook on the underside of the housing.(Fig. 11)
4. To remove the collection bag, disconnect the attach-
ments in the reserve order.
GB-4
(Fig. 1-2)
(fig. 9-11)
(fig. 3-8)