Faber MatriX 450/500 Bedienungsanleitung Seite 11

5.2.3 Control/advice function
The I.T.C. controls the entire process in the background and sends
notifications to the App. The remote control handset flashes orange
or red to indicate that you should consult the App.
When flashing orange the fire is functioning correctly but the App is
giving advice, for example to replace the batteries of the remote
control or that the maintenance period has expired.
When flashing red there is a malfunction whereby the fire can no
longer function. In most cases the cause is indicated in the App
under "Notice" in the dashboard.
5.2.4 Registration
The I.T.C. registers the amount of gas used, running and stand-by
hours. On the basis of this information, the I.T.C. calculates the
maintenance term.
The calculated gas consumption is a good approximation.
The use and consumption is clearly displayed in the statistics. The
I.T.C. also registers the nature of any malfunctions.
5.2.5 Control
The I.T.C. monitors the room temperature and the temperature of
the controller. If the selected temperature is exceeded the fire
switches to stand-by mode.
The fire is turned off and switched to stand-by mode if:
- there has been no manual control input or ECO command for
16 hours.
- when using the Thermostat and ECO functions the fire has
operated for more than 2 hours at maximum settings for
flame height and burner width.
- the I.T.C. is no longer receiving temperature data from the
remote control handset.
6 I.T.C. installation/configuration
The controller is factory-set with the correct information such as
item number, device name and capacity. These specific device
details are needed for the correct operation and calculations in the
I.T.C. App.
The remote control handset is already linked to the controller so
that the fire is ready for use with the remote control.
For correct functioning of the thermostat and ECO+ function it is
necessary that the remote control is placed in the wall bracket (fig.
1.4).
For full functionality of the I.T.C., in combination with a Smartphone/
tablet, a Wi-Fi- internet connection is required.
6.1 Wall bracket remote control
For correct functioning of the Thermostat and ECO+ function it is
necessary to place the remote control in the wall bracket. The
remote control is also the room temperature sensor and for that
reason the wall bracket must be installed:
- 1.5m above the floor.
- outside the radiation area of the fire.
- away from corners of the room, windows, open doors and
heat sources such as central heating radiators.
6.2 Linking remote control and I.T.C.
Press the "Pair" button (fig. 1.1B) for approximately 5 seconds on
the I.T.C. controller until the LED flashes green rapidly. As long as
the LED flashes green (± 1min.) the remote control can be linked.
The connection is accomplished by pressing any button on the
remote control. The LED flashes green a couple of times and will
turn off as soon as the connection is made.
> Please note:
Before proceeding make sure all functions operate with the
remote control.
6.3 Connecting I.T.C. with Wi-Fi
Press the "Pair" button (fig. 1.1 B) of the I.T.C. controller until the
LED flashes orange rapidly. You now have approximately 1 hour to
link the Wi-Fi connection via Smartphone, tablet or computer to
your Wi-Fi network.
Establish a connection with the "fabersetup.com" Wi-Fi-network.
Please note: it may take a few minutes before the Faber network
becomes visible on your network after pressing the pair button.
Open your browser and type the address * "fabersetup.com"
* This step may be carried out automatically by your mobile phone.
Click on Wi-Fi settings top left in the screen.
Select your home network and type in your router password.
If your home network has a hidden name you should enter the
name of your network in the field SSID. Please note: always only
choose 1 method.
Then click 'connect' to make the connection.
After this you should, if it is not done automatically under Wi-Fi
settings, repair the connection of your Smartphone with your home
network.
After several minutes, if the I.T.C. displays a small number of green
pulses every 30 seconds, the connection has been made. If the
I.T.C. does not connect, repeat the above procedure.
6.4 Connect Smartphone with I.T.C.
Download the Faber I.T.C. App. for Smartphone.
APP store:
iPhone
Google Play:
Android Smartphones. (4.01) or higher
Please note: When using your Smartphone it is necessary for the
remote control to be placed in the wall bracket.
Follow the directions of the App. and establish a connection with
the I.T.C. controller.
The system is now ready to use.
1 1
E N G
- U s e r m a n u a l