Manufacturer's Guarantee - ghd aura Bedienungsanleitung

EN
cleaning your ghd hairdryer
1. To ensure that your ghd hairdryer operates at the optimum efficiency,
Do Not Reproduce
always ensure that the rear filter is kept clean by regularly cleaning it.
Damage caused by failure to comply with these cleaning instructions is
not covered by the manufacturer's guarantee.
2. To do this first unplug the hairdryer from the mains power supply.
3. Never immerse the appliance in water.
4. Do not use a steam cleaner.
5. Wipe the outside of the ghd hairdryer with a damp cloth. Do not use sharp or abrasive
detergents or corrosive products.
6. Always use the ghd hairdryer with the genuine ghd filter.
7. Never operate the ghd hairdryer without a filter attached.
Rotate the ring with the air inlet filter
counterclockwise and then remove.
storage
1. Always allow the ghd hairdryer to cool down before storing away.
Do Not Reproduce
2. When the ghd hairdryer has cooled down, fold the power cord in the same way as it was first
delivered in its packaging. Do not wrap the power cord around the ghd hairdryer as this can
strain the cord and cause premature power cord failure.
7
Push out metal filter from rear housing.
Rinse and dry the filter or take a soft
brush and gently remove any dust and hair
from it. After cleaning the filter, re-attach
and secure by rotating clockwise.
failure to operate
Your ghd styling appliance is a high performance product and if the unit is subjected to large fluctuation in
mains power during use it may go into fail-safe mode to protect the unit from damage. Therefore, in the Do Not Reproduce
unlikely event that your ghd product does not operate correctly, check that the ghd product and mains power
supply are switched on, and that power is available.
If your product stops working, please follow the procedure below:
1. Switch off the unit
2. Unplug the unit from the plug socket
3. Wait for 5 seconds and then plug the unit back into the wall
4. Switch the unit back on
If this occurs repeatedly, please contact your local ghd service centre.
For UK plugs, please ensure that the fitted fuse is intact and functioning; if it is not replace it with an
identically rated British Standard Fuse.
If in doubt or for further advice please visit the help section of ghdhair.com or contact an approved ghd
stockist or contact ghd customer services for further advice.

manufacturer's guarantee

All ghd electrical products are individually tested before leaving the factory. However in the unlikely event of
the product proving defective due to faulty workmanship or materials, then, at its sole discretion, ghd will
repair or replace the product at no charge with an identical or equivalent product within one year from the
original date of purchase. A replacement product assumes the remaining warranty of the original product or
180 days, whichever provides longer coverage for you. When a product is exchanged, any replacement item
becomes your property and the replaced item becomes property of ghd.
To claim under this guarantee please visit 'ghdhair.com/returns' and follow the
on-screen instructions to complete your return. Please ensure that you include
a proof of purchase with any returned product. This guarantee only applies to
genuine ghd products purchased through ghd-approved stockists, and does not
cover products repaired or serviced by anyone other than ghd personnel or ghd
representatives. Note that this guarantee may be invalidated where serial numbers
or identification have been erased, damaged or modified. This does not affect your
statutory rights.
*If you do not have access to the internet please return your ghd electrical product to the closest ghd address as printed in this
leaflet or on the packaging, together with your proof of purchase. For customers in Australia and New Zealand, please phone your
Do Not Reproduce
closest ghd office on the number printed in this leaflet.
The guarantee does not include:
1. Damage caused by misuse, improper treatment or violent usage.
2. Damage caused by failure to comply with these instructions for use.
3. Damage caused by connecting this appliance to the incorrect voltage.
4. Damage caused by connecting accessories (e.g. nozzles, diffusers etc) supplied by other manufacturers.
5. Minor faults which do not significantly affect the value of the dryer or its effective use.
6. Normal wear and tear.
8