Accessories; Environmental Protection; Technical Data - Metabo KPA 18 LTX 600 Originalbetriebsanleitung

en ENGLISH
- Now gently press the rod knob (8) to advance the
toothed rod until it comes in contact with the
cartridge.
7. Use
7.1 Multifunctional monitoring system
If the device switches off automatically, the
machine electronics have activated automatic
protection mode.
Causes and remedies:
1. Battery pack almost flat (the electronics
prevent the battery pack from discharging totally
and avoid irreparable damage).
If the battery pack is almost flat, it must be
recharged.
2. Long continuous overloading of the machine will
activate the temperature cut-out.
Leave the machine or battery pack to cool.
3. If the current is too high (for example, during
extended periods of overloading) the device is
switched off.
Using the trigger switch, turn off the device (9)
and remove the battery pack. Determine the
cause of the problem and resolve it.
7.2 Setting the feed rate
Set the feed rate using the adjusting wheel (10).
7.3 Switching on and off
Switching on: press the trigger switch (9).
Switching off: release the trigger switch (9). Note:
The toothed rod is automatically retracted slightly to
avoid dripping.
However, if you activate the trigger switch at brief
intervals (shorter than 1 second), the rod is not
automatically retracted. This allows precise dosage
of volumes.
Note: The motor switches off automatically if either
the cartridge or the plastic bag is empty.

8. Accessories

Only use original Metabo battery packs and Metabo
accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Batter chargers: ASC Ultra, ASC 30-36, etc.
Battery packs with different capacities. Buy
battery packs only with voltage suitable for your
power tool.
Order no.: 6.25596 ....2.0 Ah
Order no.: 6.25346 ...3.5 Ah
etc.
Conversion kit 400 ml Order no.: (315418210
343444950)
Comprising a short toothed rod (7) and 400 ml tube
(3) for replacing parts.
10
Conversion kit 600 ml Order no.: (315418070
343444960)
Comprising a short toothed rod (7) and 600 ml tube
(3) for replacing parts.
Installation instructions for conversion kit:
See page 2, fig. C.
- Unscrew the tube (3).
- Extract the screw from the rod knob (8) and pull
the rod knob (8) back from the rod (7).
- Pull the toothed rod forwards from the motor
housing.
- Extract the screw and dismantle the components
(16) to (17) from the rod.
- Insert the rod from the conversion kit towards the
front.
- Attach the rod knob (8) on top and fasten it in
place with a screw.
- Fit components (16) to (17) on the other rod and
fasten in place with a screw.
- Screw the tube from the conversion kit together
tightly.
For a complete range of accessories, see
www.metabo.com or the catalogue.
9. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.

10. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
tools, packaging and accessories.
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Only for EU countries: never dispose of
power tools in your household waste! Used
power tools must be collected separately and
handed in for environmentally compatible recycling
in accordance with European Directive 2002/96/EC
on waste electrical and electronic equipment and its
implementation in national legal systems.
Discharge the battery pack in the power tool before
disposal. Prevent the contacts from short-circuiting
(e.g. by protecting them with adhesive tape).

11. Technical Data

Explanatory notes on the specifications on page 3.
+
Changes due to technological progress reserved.
U = Voltage of battery pack
v = Feed rate
F = Extrusion force
+