Operation - TFA 35.1152 Bedienungsanleitung

TFA_No. 35.1152_Anleitung 11.10.2018
SKY– Wireless weather station
Therefore, please note the following steps:
• The recommended distance to any interfering sources like computer screens or TV sets is at least
1.5 - 2 meters.
• Within concrete walls (reinforced with steel) such as basements, the received signal is naturally
weakened. In extreme cases, please place the unit close to a window to improve reception.
• During night-time, the atmospheric interference is usually less severe and reception is possible in
most cases. A single daily reception is adequate to keep the accuracy deviation under 1 second.

7. Operation

• During the operation, all successful settings will be confirmed by a brief beep tone.
• Press and hold the °C/°F – or ALARM ON/OFF + button in setting mode for fast mode.
• The device will automatically quit the setting mode if no button is pressed for 15 seconds.
7.1 Manual setting of the clock and calendar
• Press and hold the MODE/SET button for 3 seconds. The 24 HR digit (default) will be flashing.
Press the °C/°F – or ALARM ON/OFF + button to choose 12 Hr or 24 Hr system.
• Press the MODE/SET button to make the settings in the following sequence: The time zone TZ
(default: 0), hours, minutes, seconds, year, month, day, and day-of-week language (default: GE).
Press the °C/°F – or ALARM ON/OFF + button to adjust the settings.
• Confirm with the MODE/SET button.
• The manually set time is overwritten once the DCF time signal is successfully received.
7.1.1 12/24-hour display setting
• In setting mode you can choose between the 12- or 24 hour system.
• In the 12-HR system AM (before noon) or PM (after noon) appears on the display.
7.1.2 Time zone setting
• You can make the time zone correction (+12/-12) in setting mode.
• The time zone correction is needed for countries where the DCF signal can be received but the
time zone is different from the DCF time (e.g. +1=one hour plus).
24
10:58 Uhr Seite 13
SKY– Wireless weather station
7.1.3 Day-of-the week language
• In the setting mode you can set the day-of-the week language: German (GE), French (FR), Spanish
(ES), Italian (IT), Dutch (NE), Danish (DA), Russian (RU) and English (EN).
7.2 Temperature unit setting
• Press the °C/°F – button on the base station to change between °C (Celsius) or °F (Fahrenheit)
as temperature unit. Press the °C/°F button in the battery compartment of the outdoor transmit-
ter, to change between °C (Celsius) or °F (Fahrenheit) as temperature unit.
7.3 Display of seconds or day-of-the-week
• Press the MODE/SET button to change the display from seconds to weekday permanently.
8. Alarm function
• Press the MODE/SET button again to enter the alarm mode.
• AL and 07:00 (default) or the last adjusted alarm time appear on the display.
• Press and hold the MODE/SET button.
• The hour digits flash.
• Press the °C/°F – or ALARM ON/OFF + button to adjust the hours.
• Confirm the setting with the MODE/SET button and set minutes in the same way.
• Confirm with the MODE/SET button.
• Press the MODE/SET button again.
• The display shows the current time.
• Press the ALARM ON/OFF + button in normal mode, to activate or deactivate the alarm function.
• The alarm symbol appears/disappears.
• When the alarm is activated, the alarm starts to ring when the set alarm time is reached.
• The alarm symbol flashes.
• If the alarm is not stopped manually, the ascending alarm tone automatically turns off after two
minutes and the alarm will be reactivated at the same set time on the following day.
• Press any button (except SNOOZE/LIGHT) and the alarm will stop.
• Press the SNOOZE/LIGHT button to activate the snooze function.
• Once the snooze function is activated, Zz will be flashing on the display.
• The alarm will be interrupted for 5 minutes.
25