Herunterladen Inhalt Inhalt Diese Seite drucken

Auslegungsbeispiel; Rechnerische Ermittlung Der Ventileinstellgrößen; Calculation Of Valve Settings - CasaFan AVE 100 Montage- Und Betriebsanleitung

Automatische abluftventil
Inhaltsverzeichnis

Werbung

Auslegungsbeispiel

Design example
1. Rechnerische Ermittlung der Ventileinstellgrößen
Ermittlung des genauen Werts der Ventileinstellgrößen muss der hinter
jedem Ventil vorhandene Unterdruck bei Grund- und Hauptlüftung berechnet
werden.
Hierbei sind die folgenden Schritte abzuarbeite:
1) Festlegung der Absaugvolumenströme pro Absaugstelle
2) Festlegung der Gleichzeitigkeit
3) Berechnung der Strömungsverluste im Kanal
3a) Festlegung des Kanalmaterials
3b) Festlegung des Kanaldurchmessers
3c) Berechnung der Rohrreibungszahl λ
3d) Berechnung des Druckverlustes durch Rohrreibung
3e) Berechnung des Druckverlustes durch Abzweige, Bögen etc.
3d) Summieren zum Gesamtdruckverlust
4) Auswahl des Ventilators
Für unser Beispiel wird die
genaue Berechnung auf den
folgenden Seiten gezeigt.
Beispiel einer Anlage
Beispiel
Berechnung des Unterdrucks hinter den Ventilen im Strang C:
Hauptlüftung (Gleichzeitigkeit = 100 %)
Unterdruck am saugseitigen Ventilatorstutzen: 80Pa
Druckverluste Strang SK-C0-C1(C3)
Strang SK
Übergangsstück SK-C0
Strang C0
4 Bögen
Übergangsstück C0-C1/C2/C3
Strang C1(C3)
BSE 100
Unterdruck am Ventil C1,C3 : 80 Pa-26Pa = 54 Pa
Unterdruck am Ventil C2:
80Pa-29Pa = 51Pa
Diese Unterdrücke sind im Vergleich zu Strang A und B zu groß. Bei einer
Ventileinstellung entsprechend diesen Werten besteht aufgrund der durch die
geringen Öffnungshübe hohen Luftgeschwindigkeit am Ventilteller die Gefahr
der Entstehung von Pfeifgeräuschen.
Abhilfe: Einbau eines Strömungswiderstandes (Blendeklappe) in Strang C0
von 20 Pa.
somit:
Unterdruck am Ventil Strang C1: 34 Pa
Unterdruck am Ventil Strang C2: 31 Pa
Unterdruck am Ventil Strang C3: 34 Pa bei Hauptlüftung
Grundlüftung (20 m³/h; Gleichzeitigkeit = 100%)
Unterdruck am saugseitigen Ventilatorstutzen: 80Pa
Druckverluste Strang SK-C0-C1(C3)
bei etwa quadratischem Verlauf der Anlagenkennlinie:
.
p
= k · V
mit
2
ges
k = 0.01278 für C1 u. C3 und
k = 0.01194 für C2
Druckverlust Ventil C1, C3:
Druckverlust Ventil C2:
Unterdruck am Ventil C1, C3: 80 Pa - 5 Pa = 75 Pa
Unterdruck am Ventil C2:
80 Pa - 5 Pa = 75 Pa
6
Zur
A0
8 m
A1
A4
3 m
1 m
A2
A5
3 m
1 m
A3
A6
3 m
1 m
2 Pa
1.8 Pa
11.5 Pa
3.5 Pa
0. 7 Pa
3.4 Pa
2.8 Pa
---------
25.7Pa
5.1 Pa
4.8 Pa
Betriebsanleitung AVE100

1. Calculation of valve settings

For exact determination of the valve settings, the subatmospheric pressure for
basic and main ventilation downstream of each valve must be calculated.
The procedure is as follows:
1) Determination of the suction volume flows per extraction point
2) Determination of the simultaneity
3) Calculation of the flow losses in the duct
3a) Determination of the duct material
3b) Determination off the duct diameter
3c) Calculation of the pipe friction coefficient l
3d) Calculation of the pressure loss due to pipe friction
3e) Calculation of the pressure loss due to branches, bends, etc.
3d) Addition to total pressure loss
4) Fan selection
Drehzahlregler
speed control
P
C0
20 m
B1
1 m
B2
1 m
Excample of installation
E xample
Calculation of the subatmospheric pressure downstream of the valves in line
C:
Main ventilation (simultaneity = 100 %)
Subatmospheric pressure on the fan suction side: 80Pa
Pressure loss line SK-C0-C1(C3)
Line SK
Transition SK-C0
Line C0
4 bends
Transition C0-C1/C2/C3
Line C1(C3)
BSE 100
Subatmospheric pressure at valve C1,C3 :
Subatmospheric pressure at valve C2:
These subatmospheric pressures are too high compared with line A and B.
With a valve setting corresponding to these values, the high wind velocity at
the valve disk due to the small opening stroke gives rise to a risk of whistling.
Remedy: Installation of a flow resisting device (restrictor) in line C0 of 20 Pa.
Resulting in:
Subatmospheric pressure at valve line C1: 34 Pa
Subatmospheric pressure at valve line C2: 31 Pa
Subatmospheric pressure at valve line C3: 34 Pa for main ventilation
Basic ventilation (20 m³/h; simultaneity = 100%)
Subatmospheric pressure on fan suction side: 80Pa
Pressure losses line SK-C0-C1(C3)
with a roughly quadratic course of the system characteristic:
.
p
= k · V
with
2
ges
k = 0.01278 for C1 and C3 and
k = 0.01194 for C2
Pressure loss valve C1, C3:
Pressure loss valve C2:
Subatmospheric pressure at valve C1, C3:
Subatmospheric pressure at valve C2:
For our example, exact
calculation is shown on the
following pages.
2 Pa
1.8 Pa
11.5 Pa
3.5 Pa
0. 7 Pa
3.4 Pa
2.8 Pa
----------
25.7Pa
80 Pa-26Pa = 54 Pa
80Pa-29Pa = 51Pa
5.1 Pa
4.8 Pa
80 Pa - 5 Pa = 75 Pa
80 Pa - 5 Pa = 75 Pa
2003-04-10

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis