Werbung
Verfügbare Sprachen
Verfügbare Sprachen
INSTRUCTIONS ON ASSEMBLY AND USE
EN
CONGRATULATIONS ON PURCHASING YOUR BIG WHEEL SCOOTER!
Please read these instructions carefully. The instructions are an integral component of the product.
Therefore, please store them and the packaging carefully in case questions arise in the future. Please
always include these instructions when you are handing on the product to a third-party. Children
should only assemble, use or repair the product when they are under adult supervision. This product
is not suitable for industrial use.
TECHNICAL SPECIFICATIONS
Item:
HUDORA Big Wheel
Item number:
14678, 14679, 14687, 14690/01, 14693, 14694, 14695, 14697,
14709, 14720, 14724, 14725, 14726, 14729, 14736, 14737, 14761,
14762, 14763, 14764, 14769
Dimensions:
approx. 88 cm in length, deck approx. 33 x 11.5 cm
Weight:
4.1 kg
Maximum user weight: 100 kg
CONTENTS
1 x scooter
1 x instruction leaflet
Other parts which may be included with the delivery in some circumstances are not required.
GENERAL INFORMATION
The product should be assembled under adult supervision only. In order to assemble it correctly,
please read the step-by-step instructions carefully. Mistakes made when assembling the product
could lead to the user or others becoming injured. We recommend folding the scooter after each use.
Please take care to work step-by-step through the assembly instructions also. Aluminium is a good
and light material but should also be handled carefully as it is not as hard as steel, for example. FAQ's
and the solutions to many technical problems can be found at: http://hudora.de/service/
BEFORE ASSEMBLY
Please use this page as a supporting document to the de-
scription of parts. These descriptions and numbers will be
referred to in the assembly steps for easier understanding.
No tools are required to assemble the product. The scooter is
delivered in its transport form (folded)! (Picture 1)
Picture 2
Picture 5
PLEASE PROCEED AS FOLLOWS TO GET THE SCOOTER
READY FOR USE (PICTURES ARE DESIGN EXAMPLES)
• Pull on the lever to the right above the running board to loosen the transportation lock (Picture 2)
• Unfold the scooter's handlebars upwards.
• Now push the folding hinge towards the handlebar stem until you hear it click into place. (Picture 3)
• Insert the handlebar grips into the T-section of the handlebar stem. Use your thumbs to press down
both locking buttons until the the grips can be easily pushed into the T-section. Turn the handlebar
grips until the locking buttons are positioned in the two openings intended for them and you hear
them click into place. Check that both handlebar grips are fitted correctly by pulling both outwards.
If they do not move, they have been assembled in accordance with the instructions. (Picture 4)
• Loosen the quick release lock on the handlebar rod by pushing the lever of the quick release lock
until the lever is parallel to the handlebar grip. (Picture 5)
• The handlebars can be locked into place at 4 different heights. Pull the handlebar rod out of the
handlebar stem until it is at the required height and the relevant button has snapped into place.
(Picture 7) The maximum height is 1040 mm, and cannot be exceeded due to the integrated
lock. If the handlebar does not sit firmly at the required height, open the quick release lock again
and turn it a few times so that the fastening bracket fits more tightly to the handlebar rod. Repeat
this process until the handlebar rod can be aligned securely. (Picture 6)
• Now close the quick release lock by pushing the lever down to the handlebar stem.
• Always check all parts before use to ensure they are fitting tightly, particularly the folding
mechanism, the handlebar locking and the wheels.
EN 14619:2004
Picture 1
Picture 3
Picture 4
Picture 6
Picture 7
HUDORA | Jägerwald 13 | 42897 Remscheid | Germany
www.hudora.de
TO GET THE SCOOTER READY FOR TRANSPORT AGAIN,
PLEASE CARRY OUT THE FOLLOWING ACTIONS
• Loosen the quick release lock by pushing the lever of the qucik release lock away from the hand-
lebar stem.
• Please press the locking button so that the handlebar rod can be moved. (Picture 7)
• Push the handlebar rod as far as it will go into the handlebar stem.
• Close the quick release lock by pushing the lever down to the handlebar stem.
• Use your thumbs to press both locking buttons in the handlebar grips and pull the handlebar grips
outwards until they are released completely from the T-section. (Picture 4)
• Push the handlebar grips down until they are parallel with the handlebar shaft.
• Pull the lever (to the right above the running board) in order to loosen the assembly lock. (Picture 2)
• Fold up the scooter by moving the handlebar rod towards the back wheel until you hear the trans-
port lock click into place.
NOTHING'S EASY AT FIRST ...
... most accidents happen to "beginners" within the first ten minutes. Particular care should be taken
during this stage.
USAGE INSTRUCTIONS
The scooter moves when a foot is used to regularly push off, just as with well-known children's
scooters. Braking is no problem either - simply step on the friction brake over the back wheel (mud-
guard).
MAINTENANCE AND CARE
Clean the product with a dry or damp cloth only and do not use special cleaning agents! Check the
product for damage or traces of wear and tear before and after each use. Store the product in a safe
place where it is protected from the elements so that it cannot be damaged. Regularly grease the
moveable parts with a light machine oil.
WHEEL CHANGE
Replacement wheels are available as accessories from http://www.hudora.de/a/Z34/ and should be
replaced when they are worn down. To change the wheels, loosen the axle fitting with two size 5
Allen keys and take the wheels off the axle. A screwdriver or Allen key can be used to push the
bearings out of the wheel to use them in the new wheel. However, it is usually advisable to change
the bearings when the wheels are changed. Put the bearings into the new wheel with the bolt spacer
and mount them to the frame with the axle screws. Make sure the axle has been screwed on tightly
before starting again!
BEARINGS
Your scooter is equipped with precision ball bearings which were filled with lubrication at high pres-
sure during manufacture. For this reason, the wheels only run easily and quickly when there is a load
on the scooter. The bearings are maintenance free. If a bearing should fail, it should be replaced
completely. Bearings are available as accessories from http://www.hudora.de/a/Z34/.
WARNING NOTICES
•
The scooter is only intended for use by one person. Only use the scooter on surfaces that are
suitable for it, i.e. those which are smooth, clean and dry. Avoid sloping ground. The brakes may
become hot if the scooter has been used for a while! They shouldn't be touched until they have
cooled down.
•
Always be considerate of others.
•
Wear suitable protective clothing for your own safety. Never use the scooter without a helmet and
wrist, elbow and knee pads. Never use the scooter without shoes!
•
Before you begin – check that all connecting elements and locking parts are fitting securely, e.g.
the folding mechanism and the height setting of the handlebar. The functions of self-securing
screw threads can be impaired after repeated loosening and tightening of the connecting
elements.
•
Do not use the scooter at twilight, at night or in poor visibility. Do not use it on roads or thorough-
fares or on slopes or hills. Avoid being in the proximity of stairs and open water.
•
The scooter is not suitable for jumps.
•
The scooter is not a vehicle in the sense of the road traffic regulations! It is intended for use on
footpaths.
•
For your own safety, please use original spare parts only. These can be sourced from HUDORA.
Do not make any structural changes. If parts become damaged or if sharp edges or corners
should develop, the product may not be used any more. If in any doubt, please contact our service
team (http://hudora.de/service/).
DISPOSAL ADVICE
At the end of the product's life, please dispose of it at an appropriate collection point in your area.
Local waste management companies will be able to answer your questions on this.
SERVICE
We make every effort to deliver faultless products. If faults do arise however, we put just as much
effort into rectifying them. Therefore, you can find numerous information on the product, replacement
parts, solutions to problems and lost assembly manuals at http://www.hudora.de/a/Z34/.
SPARE PARTS AND ORIGINAL ACCESSORIES AVAILABLE AT:
http://www.hudora.de/a/Z34/
Item no. 14678, 14679, 14687, 14690/01, 14693,
14694, 14695, 14697, 14709, 14720, 14724,
14725, 14726, 14729, 14736, 14737, 14761,
14762, 14763, 14764, 14769
As of 07/10
Page 2/6
Werbung
