Installation Instructions - Novoferm DuoPort 700 h/c Montage-, Bedienungs- Und Wartungsanleitung

GB

installation instructions

Incorrect installation renders the door manufacturer's lia-
bility null and void.
- Installation by qualified installers only -
Please read these instructions carefully prior to installa-
tion.
Intended use of garage doors
Garage doors are intended for installation in areas ac-
cessed by persons in privately used garages and they are
used to enable safe approach of consignments and vehi-
cles, accompanied or driven by people, in residential areas.
Although garage doors are tested according to national and
international stands and manufactured in accordance with the
state of the art, they can pose hazards.
Use of the doors is classified as improper particularly in the
following cases:
•
Their use does not conform to the intended use
•
Improper repair or improper servicing, particularly when
performed by incompetent persons
•
Exertion of loads exceeding normal manual force on the
handle
•
Use of inappropriate or incorrectly adjusted locking devices
or operators
•
Installation or attachment of improper components and
parts in or to the door, the door leaves, the locking system
(locks, strike plates) and/or modification of the original de-
livery status of these parts
•
Changes to or modifications of the doors or its components
•
Simultaneous operation of the handle and the key
•
Inserting fingers between the door leaf and frame when
closing the door
•
Failure to observe the assembly, operating and mainte-
nance instructions, respective country-specific standards
and guidelines as well as applicable safety regulations
•
The door is not in a technically and operationally perfect
condition
•
Door elements are not children's toys
The door element is not suitable for use by persons (including
children) with limited mental, physical or sensory capacities or a
lack of experience or knowledge.
A door element is not suitable for use as a load-bearing com-
ponent. Installation must be carried out vertically to ensure that
the hinge axes are in a vertical position.
Keep these installation, operating, and maintenance instructions in a safe place during the entire service life of the garage door!
"DuoPort 700" double leaf hinged door
General information:
"DuoPort 700 h/c" double leaf hinged doors are intended for
manually operated use.
They must NOT be power operated!
The door must be operated with a self-acting locking device for
the open end position of both leaves.
We can provide suitable locking devices [
they can be executed – according to structural conditions - on
site, example [
Operation of the door – particularly models opening out-
wards – in windy conditions can be dangerous!
Scope of delivery:
Pre-assembled door element [
Before commencing installation, make sure you have
•
•
• • • •
Important:
•
•
•
- 7 -
].
1.45
1.10
Two persons
The following tools:
Measuring tape (5m), spirit level, hammer drill with bits
∅10mm (metal drill drilling depth min. 75 mm, stone drill
drilling depth min. 130 mm), hammer, wedges, Phillips
screwdriver, alternatively cordless screwdriver with screw-
driver bit PH 2 and PZ 3, Allen key SW 3, 4 and 6 prefera-
bly with spherical head, ...
Fastening and filling material suitable for the structural
conditions.
Caution: Prior to use, please make sure the frame
dowel plugs included in the delivery are suitable for
the structural conditions.
Characteristic values in case of suitability and use:
- Drill diameter 10 mm
- Borehole depth (wall) ≥ 55 mm,
- Anchoring depth (wall) ≥ 40 mm,
- Tightening torque = 8 Nm
The garage door must be mounted in the finished
opening and on the finished floor!
To be on the safe side, please compare the dimensions of
the installation opening/garage with the co-ordinating size
of the door PRIOR TO commencing installation [
−
Opening dimensions for installation BEHIND the
opening:
Min. opening width
= Co-ordinating width (co-ord. width)
Min. opening height
= Co-ordinating height (co-ord. height)
Min. rebate width right/left/top = 25 mm
⇒ Min. garage width = Co-ord. width + 50 mm [
Min. garage height = Co-ord. height + 25 mm [
−
Opening dimensions for installation IN the opening
Min. opening width/garage width
= Co-ord. width + 50 mm [
Min. opening height/garage height
= Co-ord. height + 25 mm [
Make sure the delivery is complete PRIOR TO commenc-
ing installation.
]; alternatively
1.40c
] including accessory set (AS)
].
1.15
1.15a
1.15c
]
1.15b
]
1.15d
]
]