Pufferspeicher und solar-pufferspeicher (8 Seiten)
Inhaltszusammenfassung für oventrop Hydrocor HP
Seite 1
Premium Armaturen + Systeme Wärmedämmung für „Hydrocor HP/HS“ Montageanleitung Vor Montage der Wärmedämmung die Anleitung vollständig lesen! Montage nur von einem Fachhandwerker ausführen lassen! Anleitung an den Anlagenbetreiber weitergeben!
99W nach DIN EN 12977 Diese Vlies-Dämmung dient dazu, die Stillstandsver- für Typ 1000 Art.-Nr. 1385110 luste der Oventrop Speicher vom Typ „Hydrocor“ zu Höhe/ Außendurchmesser (mm) 2.058/1.090 reduzieren. Die Wärmeverluste wurden von Oventrop nach der Norm DIN EN 12977 ermittelt. Die Wärme- Dämmstärke (mm)
Seite 3
Wärmedämmung für „Hydrocor HP/HS“ Montage Montage der Wärmedämmung auf „Hydrocor“-Speicher Den direkten Kontakt der Wärmedämmung mit der Wand vermeiden. Zwischen Speicher und Wand einen Abstand von mindestens 400 mm einhalten. Die PS-Mäntel dürfen beim Transport nicht geknickt werden. Knickspuren sind äußerlich dauerhaft sichtbar.
Seite 4
Montage Wärmedämmung für „Hydrocor HP/HS“ PU-Deckel von oben auf den Speicher legen. PS-Deckel aufsetzen. Flanschrosetten (mitgeliefert) auf Anschluss-Stutzen aufstecken. Die Montage der Wärmedämmung auf den Speicher ist abgeschlossen. OVENTROP GmbH & Co. KG Paul-Oventrop-Straße 1 D-59939 Olsberg Telefon +49 (0) 29 62 82-0 Eine Übersicht der weltweiten...
Valves, controls + systems Thermal insulation for “Hydrocor HP/HS” Installation instructions Read installation instructions in their entirety before installing the thermal insulation! Installation must only be carried out by a qualifi ed tradesman! Hand installation instructions over to the user of the system!
DIN EN 12977 standard. The thermal Thickness of insulation (mm) insulation can only be combined with the storage cylin- ders “Hydrocor HP” and “Hydrocor HS” of different si- Standby heat loss 121W acc. to DIN EN 12977 zes.
Seite 7
Installation Thermal insulation for “Hydrocor HP/HS” Fixing of the thermal insulation to the storage cylinder “Hydrocor” Avoid direct contact of the thermal insulation with the wall. Keep a minimum distance of 400 mm between the storage cylinder and the wall.
Seite 8
Installation Thermal insulation for “Hydrocor HP/HS” Place the PU cover on top of the storage cylinder. Mount the PS cover. Mount the (supplied) fl ange rosettes over the connection pipes. Installation of the thermal insulation is completed. OVENTROP GmbH & Co. KG Paul-Oventrop-Straße 1...
Seite 9
Robinetterie « haut de gamme » + Systèmes Isolation thermique pour « Hydrocor HP/HS » Notice d’installation Lire intégralement la notice d’installation avant le montage de l’isolation thermique ! Ne faire effectuer le montage que par un professionnel qualifi é ! La notice d’installation doit être remise à l’utilisateur de l’installation !
Epaisseur de l’isolation (mm) tion thermique est uniquement prévue pour l’utilisa- Pertes à l’arrêt 121W selon DIN EN 12977 tion avec les ballons d’eau chaude « Hydrocor HP » et Classement au feu DIN 4102 B1 « Hydrocor HS ».
Seite 11
Montage Isolation thermique pour « Hydrocor HP/HS » Montage de l’isolation thermique sur le ballon d’eau chaude « Hydrocor » Eviter tout contact direct de l’isolation ther- mique avec le mur. Prévoir un écartement minimal de 400 mm entre le ballon d’eau chaude et le mur.
Seite 12
Montage Isolation thermique pour « Hydrocor HP/HS » Positionner par-dessus le ballon d’eau chaude le couvercle en PU. Monter le couvercle en PS. Faire glisser les rosaces (jointes à la livraison) sur les manchons de raccordement. Le montage de l’isolation thermique est terminé.