Inhaltsverzeichnis
Werbung
Beachtung der Montagehinweise
und Umgebungsbedingungen
ist keine ständige Wartung er-
forderlich.
7. Entsorgung/
Recycling
Beachten Sie bei der Entsorgung
defekter Geräte die gültigen Vor-
schriften hinsichtlich Recycling
und Entsorgung. Kunststoffma-
terialien sind mit entsprechenden
Symbolen gekennzeichnet.
5. Installation
For the mounting and
operation of electrical
apparatus, the respecti-
ve national safety regulations as
well as the general rules of engi-
neering will have to be observed.
5.1 Mounting
The quick mounting plate is used
for mains connection and fixing of
the body of luminaire. At least two
screws diagonal arranged Ø 4.5
mm (fig. 3) have to be used. Using
impact dowels a damaging of the
drill hole by direct impact to the
plastic material must be avoided.
The letters „TOP" should be in
an upper position, if vertically
mounting is requested „TOP"
should be on the left-hand-side.
Mains connection must be in
accordance to terminal marking
(L(U), N(0), PE). (fig. 5). Pay atten-
tion to a tight fit of the terminal
screws! Unused cable entries are
left with their locking plug fitted
(IP protection).
In order to fix the luminaire, the
opening in the body of the lu-
minaire is placed on the guide
pin (fig. 1) of the quick mounting
plate. Then all four corners of the
body of the luminaire are pushed
down until they distinctly lock in
on the quick mounting plate (the
snap hooks engage in the quick
mounting plate). When installing
the luminaire with IP 54 protec-
tion, the IP 54 accessories kit is
to be fixed with 4 screws.
Using the pertaining self-
cutting screws 3.5 x 16, the bowl
is evenly screwed down on the
quick mounting set.
Only use handforce to tighten the
screws (max. 0.8 Nm)!
For lamp replacement or ad-
dressing, the snap hooks of the
screen are detached with a slot-
ted screw driver (fig. 6).
In order to detach the body of
luminaire from the quick moun-
ting plate, a slotted screw driver
is inserted into the lateral recess
on the reflector (fig. 7). Through a
slight lateral lever action towards
the outer edge, the snap hook is
released. When slightly pulling
the body of luminaire from the
inside, it disengages from the
quick mounting plate. After ha-
ving released all four snap con-
nections, the body of luminaire
can be removed from the quick
mounting plate; in case of the IP
54 version the 4 screws will have
to be unscrewed.
5.2 Mounting accessories
Pendulum set
(CEAG No. 400 71 345 972)
Wall bracket
(CEAG No. 400 71 345 974)
Quick mounting plate
(CEAG No. 400 71 345 980)
IP 54 accessories kit
(CEAG No. 400 71345 975)
A special version for pendulum
suspension with IP 54 protec-
tion is available under the CEAG
No. 400 71 345 944.
Chain suspension
(CEAG No. 400 71 345 973)
Wire guard
(CEAG No. 400 71 348 370)
5.3. Addressing
(only CG-S luminaires)
Before fitting the screen or bowl,
the addressing of the individual
luminaires will have to be per-
formed. To do so, the desired
address (1 - 20) is set on the
address switch by means of a
suitable screw driver (Arrowhead
to No., fig. 9). If the luminaire
should not be monitored the code
0/0 has to be selected.
6. Servicing/
Maintenance
Observe the relevant national
regulations which apply to the
maintenance, servicing and
check of electrical apparatus!
On condition of an appropriate
operation and of observing the
mounting instructions and en-
vironmental conditions, no per-
manent servicing will be required.
7. Disposal/
Recycling
When a defective apparatus
is disposed of, the respective
national regulations on waste dis-
posal and recycling will have to
be observed. Plastic parts have
been provided with respective
symbols.
9
Werbung
Inhaltsverzeichnis
