Werbung
Verfügbare Sprachen
Verfügbare Sprachen
b. Fix the hook-on bracket (Figure ❻)
- Place the bracket on the ground and against the wall and mark the drilling points A. These give the position of the bottom
fasteners. Replace the brackets in alignment with the drilling point A to locate drilling points B. These give the position of
the upper fasteners. In case of special support, use proper anchors. Position and screw the wall brackets.
1.3.2
Electrical connexion
- The appliance should have a 230 / 50Hz power supply. The panel heater must be connected to the mains by a 2-wire cable
for Mechanical Device or 3-wire cable for Electronic Device (Brown= Phase, Blue = Neutral, Black = Pilot wire) by means of
a connexion box. In humid areas such as bathrooms and kitchens the power socket must be installed at least 25 cm above
the floor. The installation should be fitted with a double pole break device with a break of at least 3 mm.
- Connection to earth is prohibited / Do not connect the pilot wire (black) to earth. If a driver or driven device is
protected by a 30mA differential (for example for bathroom) it is necessary to protect the power supply of the pilot wire on
that differential.
- This device must be installed with a remotely controllable programming system. This type of system can be
connected via the pilot wire of the device.
Commands
Received
Oscilloscope
Ref/Neutral
Mode
obtained
Panel heater cable
Phase = Brown
Neutral = Blue
Pilot Wire = Black
Wall mounted installation (Figure ❼)
1.3.3
- Place the device inclined on the brackets C and rotates the device to place it on the brackets D. Lowering the device on the
bracket. A click indicates that the device is attached and locked. To unlock the attachment tab, grab a screwdriver and
push the tab (at the top left of the attachment tab behind the device) towards the wall. Lift the device while holding the tab
with the screwdriver. Tilt it forward and remove it from the supports C.
2. Utilisation
2.1 How to fix the comfort mode? (Figure ❽)
- The Comfort mode allows setting the desired temperature using the
control knob.
- Put the switch H on
, and then set the control knob I on the desired
position, the heating indicator G lights if the ambient temperature is
lower than desired one. Wait until the temperature stabilizes.
2.1.1 How to fix the Eco mode?
- ECO mode allows lowering the temperature of Comfort mode from 3 to 4°C during unoccupied periods of the room. It is
recommended that this mode should be used if the room is unoccupied for more than 2 hours. Put the switch H on ECO and
then set the control knob I to the desired position, the heating indicator G lights if the ambient temperature is lower than
desired ECO temperature. Wait until the temperature stabilizes.
2.1.2 How to fix the Frost Free mode?
- It is the position of the switch that keeps the temperature at approximately 7 ° C in the room during prolonged absence from
the house (usually more than 24 hours). Put the switch H on
2.1.3 How to program your device in Comfort, ECO or Frost Free mode?
- Devices equipped with an electronic thermostat are able to receive orders. There are two solutions:
- By pilot wire (black wire) for devices without plug thanks to the system Chronopass or a wall pilot wire box
- By carrier current with an interface on each device in addition to a Chronopass system or a wall carrier current box.
Absence de signal
CONFORT
Phase
Electricity
grid
Neutral
Complete
altermation
Half/altermation
230 V
ECO
ANTI - FREEZE
st
1
case: One heater
nd
2
case: Multiple
heater
G
H
I
.
Negative
Half/altermation
– 115V
STOP HEATING
LOAD SHEDDING
2 possible cases:
Unpiloted device
Pilot wire not connected
To devices with reception box
or central programming
Indicator for heating. It indicates the
periods in which the resistance is working.
With a stabilized temperature, it flashes
and if the temperature is too high, it stops.
Slider or switch
Control knob of the temperature
Positive
+ 115V
4
Werbung
