Listen To The Fm Radio - RADIO.CUBO TS522D+ Bedienungsanleitung

LISTEN TO THE DAB RADIO
1. The scan operation must be performed at fi rst start-up. The DAB icon on the display will
light up and the scanning process will start (this might take a few minutes)
2. On the remote control, use the MODE button to select the DAB mode. From the main unit,
press the MODE knob to enter the various modes and select DAB.
3. Press INFO to visually display information about the selected radio station (depending on
availability offered by the station - broadcaster)
4. Using the remote control, press the buttons
DAB stations. From the main unit, use the MENU/SELECT knob to listen to the next or
previous scanned DAB station.
5. Press SCAN to perform a full scan of the radio stations in DAB mode.

LISTEN TO THE FM RADIO

1. On the remote control, use the MODE button to select the FM mode. The display will show
an FM frequency, e.g. "102.5". The FM icon will light on the display. From the main unit,
press the MODE knob to enter the various modes and select FM.
2. Using the remote control, press the buttons
press increases or decreases the frequency by 50 kHz. From the main unit, use the MENU/
SELECT knob to increase or decrease the FM frequency.
3. Press and hold either button to fi nd the next or previous available radio frequency,
or press SCAN from the remote control to directly search for the next available station.
When a station is found, the search stops automatically. From the main unit, use the BT
PAIR/SCAN knob to fi nd the next available FM frequency.
4. Press INFO to visually display information about the selected radio station (depending on
availability offered by the station)
5. Press INFO 4 times to access the MONO/STEREO function of the FM station. Press
ENTER to toggle between MONO and STEREO. In STEREO mode, this icon will light up
on the display .
STORING AND RECALLING A RADIO STATION (PRESETS)
1. To store your favorite stations to memory locations (presets) from 1 to 5, proceed as
follows:
2/7
1/6 3/8
Press and hold the button
you want to store that station until the display shows "STORED #" (# indicates the number
where will be stored, e.g. "STORED 3" – stored in the preset no. 3)
2. To store your favorite stations in memory locations (presets) from 6 to 10, proceed as follows:
3. Press SHIFT once;
1/6 2/7 3/8
Press and hold the button
you want to store that station until the display shows "STORED #" (# indicates the number
where it will be stored, e.g. "STORED 6" – stored in the preset no. 6)
to navigate through the list of scanned
to browse the FM frequencies: one
4/9 5/10
corresponding to the number where
4/9 5/10
corresponding to the number where
32
4. You can store up to 10 DAB radio stations and 10 FM radio stations (the radio
frequency of the FM station saved by default on all presets is 87.50 MHz).
5. To retrieve one of the 10 stored presets, proceed as follows:
For stored presets 1 to 5 press one of the buttons
6. For stored presets 6 to 10 press SHIFT once (the display of the main unit will show
"SHIFT") and then the button corresponding to the desired preset.
PAIRING, CONNECTION AND OPERATION MODE OF THE UNIT THROUGH THE
BLUETOOTH WIRELESS TECHNOLOGY
The TS522D+ radio can be paired with most Bluetooth devices 2.0 and 2.1. The pairing may
differ from device to device. Refer to the instruction manual of your Bluetooth device for the
correct pairing with the unit.
1. On the fi rst access to this mode, the unit will go into the "waiting for connection" status,
the LED will fl ash slowly, and in this condition it will be possible to associate a device that
has already been paired. If the device you want to connect has Bluetooth turned on, it will
automatically connect to the radio.
2. To connect a new device, press the PAIR button for about 4 seconds until the LED fl ashes
quickly ("waiting for pairing" status). Turn on your device.
3. Turn on your Bluetooth device (for example a SmartPhone), enter the Bluetooth setup
menu and scan for available devices. In the list of found devices the label TS522D+ will
be shown.
4. Connect the device to the TS522D+ unit, the device will show the "Connected" status and
the radio LED will change from fl ashing to solid (if the pairing was successful).
5. At this point, with the TS522D+ radio it will be possible to wirelessly play the music stored
inside the associated device.
6. While a device is connected via Bluetooth, if you want to pair it with another Bluetooth
device, you must fi rst disconnect it by pressing and holding the PAIR button for about 3
seconds until you hear a "beep" sound, or by disabling the connection established directly
from the Bluetooth menu of the associated device. The unit will switch directly to pairing
mode and, at this point, you can connect another device.
CAUTION:
For mobile phones with Bluetooth 2.0, you will be prompted to enter a password during the
pairing process. Press the following string: 0000 (zerozerozerozero)
2/7
1/6 3/8 4/9 5/10
33