ECX Barrage ECX00019T1 Bedienungsanleitung

®
ECX00019T1/T2 | 1:24 4WD UTILITY VEHICLE RTR
EN
NOTICE
All instructions, warranties and other collateral documents are subject to change at the
sole discretion of Horizon Hobby, LLC. For up-to-date product literature,
visit horizonhobby.com and click on the support tab for this product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate various levels of
potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability of property
damage, collateral damage, and serious injury OR create a high probability of superficial injury.
CAUTION: Instructions, which if not followed, create the probability of property damage AND
a possibility of injury.
NOTICE: Instructions, which if not followed, create a possibility of property damage AND minor
injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the
features of the product before operating. Failure to operate the product correctly
can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and
requires some basic mechanical ability. Failure to operate this Product in a safe and responsible
manner could result in injury or damage to the product or other property. This product is not
intended for use by children without direct adult supervision. Do not use with incompatible
components or alter this product in any way outside of the instructions provided by Horizon
Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is
essential to read and follow all the instructions and warnings in the manual, prior to assembly,
setup or use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
Operating Safety Precautions
»
As the user of this product, you are solely responsible for operating in a manner that
does not endanger yourself and others or result in damage to the product or property
of others.
»
This model is controlled by a radio signal subject to interference from many sources
outside your control. This interference can cause momentary loss of control, so it is
advisable to always keep a safe distance in all directions around your model as this
margin will help avoid collisions or injury.
»
Never operate your model with low transmitter batteries.
»
Always operate your model in open spaces away from full-size vehicles, traffic and
people.
»
Never operate the model in the street or in populated areas for any reason.
»
Carefully follow the directions and warnings for this and any optional support
equipment (chargers, rechargeable battery packs, etc.) you use.
»
Keep all chemicals, small parts and anything electrical out of the reach of children.
»
Never lick or place any portion of the model in your mouth as it could cause serious
injury or even death.
»
Exercise caution when using tools and sharp instruments.
»
Take care during maintenance as some parts may have sharp edges.
»
Immediately after using your model, do NOT touch equipment such as the motor,
electronic speed control and battery, because they generate high temperatures. You
may burn yourself seriously touching them.
»
Do not put fingers or any objects inside rotating and moving parts, as this may cause
damage or serious injury.
»
Always turn on your transmitter before you turn on the receiver in the car. Always
turn off the receiver before turning your transmitter off.
»
Keep the wheels of the model off the ground when checking the operation of the
radio equipment.
CAUTION: Failure to exercise caution while using this product and complying with
the following precautions could result in product malfunction and/or void the warranty.
NiMH Charging Warnings
WARNING: Failure to exercise caution while using this product and comply with the
following warnings could result in product malfunction, electrical issues, excessive
heat, FIRE, and ultimately injury and property damage.
»
NEVER CHARGE BATTERIES OVERNIGHT.
»
NEVER LEAVE CHARGING BATTERIES UNATTENDED.
»
Read all safety precautions and literature prior to use of this product.
»
Never allow children under 14 years of age to charge battery packs.
»
Never attempt to charge dead or damaged batteries.
»
Never charge a battery if the cable has been pinched or shorted.
»
Never allow batteries or charger to come into contact with moisture at any time.
»
Never charge batteries in extremely hot or cold places (recommended between
50–80°F (10–26°C)) or place in direct sunlight.
»
Always use only Ni-MH rechargeable batteries. This charger cannot charge batteries
such as "heavy duty," "alkaline battery," "lithium battery," or "mercury battery."
»
Always connect to the charger correctly.
»
Always disconnect the battery and charger after charging and let them cool between
charges.
»
Always inspect the battery before charging.
»
Always terminate all processes and contact Horizon Hobby if the product
malfunctions.
»
Always make sure you know the specifications of the battery to be charged or
discharged to ensure it meets the requirements of this charger.
»
Always constantly monitor the temperature of the battery pack while charging.
»
Always end the charging process if the charger or battery becomes hot to the touch
or starts to change form during the charge process.
BOX CONTENTS
Body Barrage ® 1:24 4WD Scaler: RTR ECX00017
Transmitter 2.4 GHz, 2 CH (4 AA batteries included) ECX10003
Charger USB, 4 cell 4.8V NiMH, ECX Micro DYNC1060
Battery NiMH, 220mAh, 4.8V DYNB0007
Motor Brushed 050, with Pinion DYNS1203
ESC/Receiver 2 in 1 receiver/speed control ECX10014
Servo Waterproof mini servo ECX10008
SPECIFICATIONS
Length 9" (228.6mm)
Width 4" (101.6mm)
Height 4" (101.6mm)
Operating Weight 0.5 lb (0.20kg)
Getting Started
1
Charge the Vehicle Battery
1. Refer to charging warnings.
2. Connect the battery to the battery charger.
3. Connect the battery charger to a powered USB.
4. The battery will charge in under 2 hours.
The LED sequence for the USB charger is Red = charging, Green = charge is complete.
2
Remove the body
from the vehicle
3
Install the vehicle battery
4
Transmitter Controls
REVERSE SWITCH
Allows you to change the direction
ofsteering (ST. REV) and throttle (TH. REV)
controls (Ensure proper function with a
radio system test).
THROTTLE DUAL RATE
Adjusts the maximum
amount of throttle the
vehicle can be given
STEERING DUAL RATE
Adjusts the total
steering travel
POWER SWITCH
Power on or off the transmitter
5
Installing Your Transmitter Battery
This transmitter requires 4 AA batteries.
1. Remove the battery cover from the transmitter.
2. Install the batteries as shown.
3. Install the battery cover.
CAUTION: If using rechargeable batteries, charge only rechargeable batteries. Charging non-rechargeable
batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according
to national regulations.
6
Re-install the body
on the vehicle
OWNER'S MANUAL
BATTERY LEVEL INDICATOR
Solid Red and Green:
Battery voltage is good
(above 4V).
Solid Red: Battery voltage
is critically low (below
4V). Replace transmitter
batteries.
THROTTLE TRIM
Adjusts the neutral
point of the electronic
speed control
STEERING TRIM
Adjust to make the
vehicle drive straight
with no input at the
steering wheel
STEERING WHEEL
Control steering.
Right and Left
steering
THROTTLE TRIGGER
Controls power
to the motor
for forward or
reverse
Reverse
Forward Stop
7
Power on the
transmitter
8
Power on the
vehicle
9
Control Test
1. Do a test of the transmitter's control of the vehicle
with the vehicle's wheels off the ground.
2. Start driving slowly, and, and, if the vehicle does
not go straight, adjust the steering trim dial on the
transmitter.
When You Are Finished
10
Power off the
vehicle
11
Power off the
transmitter
12
Remove and
recharge the
vehicle battery
Binding Troubleshooting
Binding is the process of programming the receiver to recognize the GUID (Globally Unique
Identifier) code of a single specific transmitter. The included transmitter and receiver are
bound at the factory. If you need to rebind, follow the instructions below.
1. Power off the transmitter and ESC.
2. Connect a fully charged battery pack to the ESC.
3. Press and hold the bind button while powering up the ESC. After 2 seconds the ESC
will be in bind mode.
4. Release the bind button and power on transmitter. Binding is complete.
You must rebind when binding the receiver to a different transmitter.
TIP: Use the body pin that came with your vehicle to press the bind button within its
waterpoof cover.
NOTICE: Do not attempt to bind the transmitter and receiver if there are other compatible
transmitters in bind mode within 400 feet. Doing so may result in unexpected binding.
Optional FPV
The 1/24th Utility Vehicle is set up with a camera mount for an FPV camera (FPV Camera BLH8517).
Refer to the manual for the FPV version ECX00018 1/24 scale 4WD Electric FPV Utility Vehicle manual for more information.
NOTICE: If you are operating the FPV version in North America, you are required to have an Amateur Radio (HAM) license.
Visit www.arrl.org for more information.
BIND ON OFF BATT MOTOR