Sony UPA-PC105 Bedienungsanleitung Seite 25

Message Meaning/Solution
tAn abnormal condition in the film
FLS_ERR:
LAMP FAILURE scanner lamp caused an error.
Replace the lamp.
tAn abnormal condition in the film
FLS_ERR: XX YY
ZZ scanner caused a coded error
message (XX YY ZZ) to appear.
Switch the unit and film scanner
off, then switch them on again.
tAn internal communication error
HAERR
occurred inside the unit.
Touch the [Retry] button to
continue the scanning job. If the
same message appears again, touch
the [Cancel] button to cancel the
operation, then shut down the
system and switch the main unit off
and on.
HIGH_TEMP tThe temperature inside the film
scanner is abnormally high.
Wait a few minutes, then touch the
[Retry] button to continue the
scanning job.
IX240_CARRIER_ tThe cover of the IX240 carrier may
OPEN be open.
Close the cover of the IX240
carrier.
tThe IX240 cartridge is still set in
IX240_CART_IN
the film scanner.
Remove the IX240 cartridge.
tIX240 film jammed inside the film
IX240_FEED
scanner.
Touch the [Retry] button then
remove the IX240 film.
tUndeveloped IX240 film is loaded
IX240_NDEV
in the film scanner.
Load only developed IX240 film in
the film scanner.
tAn abnormal condition inside the
MECHA_ERR:
STAGE_MOTOR film scanner caused an error.
MECHA_ERR: FILM Call for service.
MOTOR
MECHA_ERR:
LENS_ MOTOR
MECHA_ERR:
P_PLATE
MECHA_ERR:
LIGHT
MECHA_ERR:
UD_POS
MECHA_ERR:
LR_POS
MECHA_ERR:
DX_SEARCH
tAn abnormal condition inside the
NGBUFF
film scanner caused an error.
Touch the [Retry] button to
continue the scanning job. If the
same message appears again, touch
the [Cancel] button to cancell the
operation, shut down the system,
then switch the main unit and film
scanner off and on.
Message Meaning/Solution
tThe carrier is not set in the film
NO_CARRIER
scanner.
Set the carrier in the film scanner.
tAn error occurred during
NO_TARG
RESERVE communication between the unit
and the film scanner.
Confirm the following:
• Film scanner power switch on.
• SCSI cable connection secure.
• SCSI ID assigned to the film
• SCSI terminator is set correctly.
Then touch the [Retry] button.
If the same message appears again,
touch the [Cancel] button to cancell
the operation, shut down the
system, then switch the main unit
and film scanner off and on.
SYS ERROR: XX YY tAn abnormal condition in the film
ZZ scanner caused a coded error
message (XX YY ZZ) to appear.
Touch the [Retry] button to
continue the scanning job. If the
same message appears again, touch
the [Cancel] button to cancell the
operation, shut down the system,
then switch the main unit and film
scanner off and on.
tA slide is still in the carrier of the
SLD_HOLDER
film scanner, or the holder may be
open.
Remove the slide from the film
scanner.
Other Messages
Message Meaning/Solution
Unable to initialise. tWrite operation to the CD-R failed.
Please insert another Insert a new CD-R then touch the
new CD. [Retry] button to continue the
operation.
tA used CD-R was inserted for the
Please ask shop staff
for assistance. write operation.
Insert an unused CD-R.
tThe image data on the storage
Unable to read. Make
sure your media. media cannot be read.
(xx:Error Code/String) Store the images on another storage
Return to opening media and then tray again. If the
screen. same message appears again,
switch the unit off and then on
again.
scanner is not in use by another
device.
Troubleshooting
25
GB