Operation - Worx WG155E Originalbetriebsanleitung

your one foot on the safety guard, then grip
the main handle, apply adequate force to
adjust, as shown in Fig. H2.
9. SPACEr guArD
Push the spacer guard in and out into place
before trimming, as shown in Fig. I. Make sure
the spacer guard is locked firmly.

OPERATION

wArNINg! Always wear the eye
protection. Never lean over the
trimmer head. rocks or debris can
ricochet or be thrown into eyes and face
and cause blindness or other serious
injury. when operating unit, check for the
following:
wear eye protection and heavy clothing.
Hold front handle with one hand and
auxiliary handle with the other hand. Keep
unit below waist level. work only from
your right to your left to ensure debris is
thrown away from you. without bending
over, keep line near and parallel to the
ground (perpendicular when edging) and
14 14
not crowded into material being cut.
Make sure that line is fed out before
operation. Make sure motor is up to full
speed before trimming.
use only 1.65mm cutting line, diameter
line. Other sizes of line will not feed
properly and will result in improper
cutting head function or can cause serious
injury. Do not use other material such as
wire, string, rope, etc. wire can break off
during cutting and become a dangerous
missile that can cause serious injury.
TrIMMINg
Hold the bottom of the trimmer head about 8
cm above the ground and at an angle. Allow
only the tip of line to make contact. Do not
force trimmer line into work area.
EDgINg (See Fig. J)
Holding the lower housing then pull upwards
the shaft, then rotate 90 degree clockwise.
(See Fig. F1)
Adjust trimmer head angle to be the lowest
horizontal setting. Then position the wheel on the
ground for edge mode. The guard has two white
Cordless Lawn Trimmer/Lawn Edge Trimmer EN
line guides to indicate the cutting line position.
Align these marks with the edge of your lawn.
While edging, allow the tip of the line to make
contact. Do not force the line. The rotation
wheel helps protect the unit and keeps the
unit from contacting the ground. Take extra
caution while edging as objects can be thrown
from the trimmer line.
AuTOMATIC LINE FEED SySTEM
When initially switching on the trimmer, a
small length of line is fed out.
A 'clattering' noise will be heard when the lines
hit the line cutter. Do NoT BE ALARMED this is
quit normal. After about 5 seconds the line will
be cut to the correct length and the noise will
reduce as the motor receives full speed.
If the noise of the line being cut can't be
heard, more line will be fed out.
To feed more line, it is first necessary to allow
the trimmer to stop completely, then restart,
allowing the motor to reach full speed.
Repeat above until you hear the lines hitting
against the line cutter. (Do not repeat this
procedure more than 6 times)
TO MANuALLy FEED THE LINE (See Fig. K1)
If required, line can be feed out manually.
To operate, press and release manual line feed
button (16), while gently pulling out the line
until the lines reach the line cutter.
If the line extends past the line cutter, too
much line has been fed out.
If too much line is fed out, remove the spool
cap and turn spool counter-clockwise until the
line is at the desired length.
TO rEMOVE THE CAP (See Fig. K2)
Press and hold in the two latches (12).
Pull cap away from the spool holder.
When refitting the spool cap.
Keep all areas of the cap and spool holder
clean.
Replace the cap, pressing firmly down
towards the spool holder to ensure cap is fully
located.
Check that the cap is correctly fitted by trying
to remove it without depressing the two
latches.
TO rEPLACE CuT LINE
For your convenience it is recommended you
buy spool and line complete.