Inhaltsverzeichnis
Werbung
Switching the tool on/off
Slide the switch-on lock A (fig. 5) forward and push
switch B. After the tool has been switched on, you do not
have to hold the switch-on lock A any longer.
To switch off just let go of the switch B.
Attention! The blades will coast for a certain
time after switch-off!
Refitting the tool / Changing the shear sys-
tems
Put the included blade guard into the blade(s) and use
protective gloves to protect yourself from injury.
Push both lateral push buttons concurrently and re-move
the shearing blades (Fig. 7).
Remove any dirt from the gear area (if necessary).
Please slightly grease the drive area using commer-
cial universal grease as described in the Maintenance
section before putting the replacement shears in place
(Fig.9).
Lead the cutting blades with the rear holding toe into
the housing of the grass shears as shown in fig. 6 and
lock the click system in place by strongly pushing on the
blade base plate.
The position of the eccentric drive does not have to be
considered when changing the blades. When the device
is switched on, the gear eccentric unit automatically
engages into the appropriate relief in the shearing blade.
The device is now ready for operation.
Hints for your work with the tool
The shrub trimmer cuts ornamental shrubs and light
undergrowth or bushes. The device is also well-suited for
ornamental cuts as, for example, for the care of graves.
The grass shears allow for clean cuts of lawn edges or
hardly accessible lawn areas.
As the device is operated with one hand
please be careful not to move the other hand
near the running cutting tools.
Maintenance
(Fig.9)
Clean the blade from any crushed plants and dirt. The
blades should be detached at least once a season for
the removal of debris. Lubricate the C pinion and the
D back of the blade with a light oil. Do not lubricate the
motor and other parts. Should the blade become dull
after a long period of use, a spare part can be ordered.
Warning! The leading edges of the blades must be oiled
to ensure proper lubrication. If the leading edges are not
oiled, blade durability may be adversely affected.
If the cutting tools have become dull after long use
please replace them with original spare parts.
Clean the device using only a brush or cloth. Do never
GB | Operating Instruction
wash down the device with water and do never dip the
device into water.
Apply protective spray to the blades after each use.
Replace blunt blades.
Always put on the blade guard after use.
Examine the tool for obvious defects and have it repaired
in an authorised service shop if required.
Storage
Always store the tool in a dry, clean place outside the
reach of children. Make sure that the place of storage
is frost-free.
Waste disposal and environmental protection
Batteries are not to be put into the rubbish. As a con-
sumer you are legally obliged to return used batteries
and accumulators. At the end of the duration of your ap-
paratus, the batteries or accumulators have to be taken
from the apparatus, disposing of them separately. You
have the possibility of delivering your old batteries and
accumulators to the local collecting points of your mu-
nicipality or to your dealer or to the distribution centers.
If your device should become useless somewhere in the
future or you do not need it any longer, do not dispose
of the device together with your domestic refuse, but
dispose of it in an environmentally friendly manner.
Please dispose of the device itself at an according col-
lecting/recycling point. By doing so, plastic and metal
parts can be separated and recycled. Information con-
cerning the disposal of materials and devices are avail-
able from your local administration.
Warranty
For this tool, the company provides the end user - inde-
pendently from the retailer's obligations resulting from
the purchasing contract - with the following warranties:
The warranty period is 36 months beginning from the
hand-over of the device which has to be proved by
the original purchasing document. For commercial use
and use for rent, the warranty period is reduced to 12
months. Wearing parts, rechargeable batteries and
defects caused by the use of non fitting accessories,
repair with parts that are not original parts of the manu-
facturer, use of force, strokes and breaking as well as
mischievous overloading of the motor are excluded from
this warranty. Warranty replacement does only include
defective parts, not complete devices. Warranty repair
shall exclusively be carried out by authorized service
partners or by the company's customer service. In the
case of any intervention of not authorized personnel, the
warranty will be held void.
All postage or delivery costs as well as any other subse-
quent expenses will be borne by the customer.
17
Please observe the following directions for the
disposal of your accumulator/battery.
Werbung
Kapitel
Inhaltsverzeichnis
