Sygonix 20 Bedienungsanleitung Seite 3

Operating instructions
Electronic safe 20
Item no. 1762987
Intended use
The safe can be used to store valuables. It has a stable steel casing and can be firmly attached
to a wall or placed on a stable surface.
It is operated with 4 batteries of type AA/Mignon. The safe can also be opened with the keys
enclosed when the batteries are flat.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Safe
• Two keys
• 4 screws and 4 washers
• Operating Instructions
Latest operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the
QR code shown. Follow the instructions on the website.
Explanation of symbols
An exclamation mark in a triangle indicates important instructions in this operating
manual that absolutely have to be observed.
The arrow symbol indicates specific tips and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Batteries
• Correct polarity must be observed while inserting the batteries.
• Batteries should be removed from the device if it is not used for a long period of
time to avoid damage through leaking. Leaking or damaged batteries might cause
acid burns when in contact with skin, therefore use suitable protective gloves to
handle corrupted batteries.
• Batteries must be kept out of reach of children. Do not leave batteries lying
around, as there is risk, that children or pets swallow them.
• All batteries should be replaced at the same time. Mixing old and new batteries in
the device can lead to battery leakage and device damage.
• Batteries must not be dismantled, short-circuited or thrown into fire. Never
recharge non-rechargeable batteries. There is a risk of explosion!
Installation
• Select a place for installation where the safe is not immediately visible or easily accessible.
This may be behind a closet door or behind books, folders, or similar.
• Installation in a partition wall (hollow wall) would also be ideal; a picture may be hung up in
front of the door.
Protect the safe from dampness and humidity. Thus, do not install the safe in rooms
with high humidity or damp basements.
• The safe can be mounted to a wall as well as on the floor, or another stable surface, using
the holes in the housing.
If the safe is locked upon delivery, use the keys enclosed to open it.
The corresponding lock is hidden behind a small, thin plastic cover, which is situated
directly right to the closing handle.
• Suitable screws and screw plugs may be necessary for installation depending on the surface.
Additional fixation with special clue or similar is possible, if the surface is suitable.
Opening/closing the safe with the key
This may be necessary when the batteries are half-flat or flat so that the safe cannot
be opened by entering the access code. The safe can be used in this way without
batteries, if desired.
• Remove the round, thin plastic cover from the lock; it is
situated directly to the right of the closing handle.
• Insert the key into the lock observing the correct
orientation and turn the key a little to the left in
anti-clockwise direction.
Hold the key in this position and turn the closing handle
to the right until it stops. Take the key out of the lock and
open the safe door.
• To close the safe, shut the safe door first. Then, turn
the closing handle to the left until it stops; the lock is
engaged.
Check the lock; you should not be able to turn the closing handle to the right.
If you accidentally turn the closing handle to the left when the safe door is open
so that both lock bolts reach out of the safe door (the safe cannot be closed now),
simply proceed as described above.
Inserting/Replacing batteries
Due to safety reasons and operating duration, only high-quality alkaline batteries
should be used and not rechargeable batteries.
• Open the safe using the keys as described above.
• Open the battery case at the back of the door; to do this, slide the cover backwards until it
can be removed.
• Insert four new "AA/mignon" batteries with the correct polarity (observe +/Plus and -/Minus).
• Close the battery compartment again.
• Replacing the batteries is necessary, when the red LED lights up when opening the safe or
the safe cannot be opened when entering the code. The access code is maintained when
replacing the batteries.
If the safe does not respond to entries on the number pad, it can also be opened
using the keys enclosed. The corresponding lock is situated under a thin plastic
cover right to the closing handle, see image above.