Balluff BAE LX-XO-PL018-E-_ _-S103 serie Anleitung Seite 4

Laser
BAE LX-XO-PL018-E-_ _-S103
Operation (continued)
Line Width vs. Depth of Field
The line width and depth of field values* ) for lasers with
450 nm, 520 nm, and 640 nm wavelengths can be seen in
the following graphs:
450 nm (blue)
600 1200
500 1000
400 800
300 600
200 400
100 200
0 0
0 400 800 1200 1600 2000
Working Distance [mm]
520 nm (green)
600 1200
500 1000
400 800
300 600
200 400
100 200
0 0
0 400 800 1200 1600 2000
Working Distance [mm]
640 nm (red)
600 1200
500 1000
400 800
300 600
200 400
100 200
0 0
0 400 800 1200 1600 2000
Working Distance [mm]
* The values only apply to lasers refocused for the distance.
)
Line Width [µm] (FWHM)
Depth of Field [mm] (total)
Poly. (Depth of Field [mm] (total))
3 english
Troubleshooting
Laser not Working?
– Is power being supplied (plug and the power supply
unit connected)?
– Is there damage to the cable, is the cable ruptured, or
is the power supply unit defective?
– Are the pins connected correctly?
Blurred Projection?
– Reset the focus ring.
– Contamination:
Blow off with dry and oil-free air, or clean with a dry
lens cloth.
We advise against the use of cleaning agents such as
denatured alcohol, etc.
Technical Data
Digital Modulation
Maximum frequency ≤ 400 kHz
Rise time < 200 ns
(Mod High ⇒ 90 %)
Fall time (Mod Low ⇒ 10 %) < 100 ns
Signal level V < +0.9 V
IL max
V > +2.2 V
IH min
Voltage range 0...30 V DC
Analog Modulation
Maximum bandwidth < 10 Hz
Linearity < 5 % (from 10 % to
100 % of the laser
power)
Active range 0...2 V DC
Impedance 100 kΩ to internal V
CC
(3.3 V)
Voltage range 0...30 V DC
Ambient Conditions
Ambient temperature –10 °C...+50 °C /
14 °F...+122 °F
Storage temperature –40 °C...+85 °C /
–40 °F...+185 °F
Relative humidity < 90 %, non-condensing
Heat dissipation < 1 W
Shock and vibration DIN EN 60068-2-6
Technical Data (continued)
Model
...-L1-... ...-L3-...
Order Code BAE0104 BAE0106
Wavelength (typical) 640 nm 640 nm
Output power 30 mW 10 mW
Laser color Red Red
Projection Line, homogeneous intensity distribution
Operating mode
Supply voltage 5...30 VDC
Operating current (max.) < 400 mA
Over temperature protection and LED pre-failure indicator,
Protection
reverse polarity and transient protection / ESD, burst, surge
Electrical isolation
Power consumption < 2.0 W
Connection
Interfaces
Aperture angle 45° 20°
Focus
Focusing area 100 mm...10000 mm
Operating temperature
Storage temperature
Wavelength tolerance
Weight
Dimensions (Ø x L)
Material
Protection class
Laser class
(EN 60825-1:2014)
These operating instructions and the Declaration of
Conformity are also available at www.balluff.com.
Headquarters Global Service Center
Germany Germany
Balluff GmbH Balluff GmbH
Schurwaldstrasse 9 Schurwaldstrasse 9
73765 Neuhausen a.d.F. 73765 Neuhausen a.d.F.
Phone + 49 7158 173-0 Phone +49 7158 173-370
Fax +49 7158 5010 Fax +49 7158 173-691
balluff@balluff.de service@balluff.de
www.balluff.com
BAE LX-XO-PL018-E-_ _-S103
...-L7-... ...-L8-... ...-P1-... ...-C1-...
BAE0107 BAE0108 BAE0109 BAE010A
450 nm 520 nm 635 nm 635 nm
25 mW 25 mW 1 mW 3 mW
Blue Green Red Red
Point,
Cross
elliptical
APC
9...30 VDC 5...30 VDC
< 300 mA < 400 mA
Potential-free housing
< 2.7 W < 2.0 W
M12 5-Pin: A-pining plug connector
I²C, RS-232 (5 V)
45° – 30° × 30°
Focusable
100 mm...
< 1000 mm
–10 °C ... +50 °C
–40 °C ... +85 °C
±10 nm
155 g
20h7 x 116 mm
Stainless steel
IP67
2M 2 1M
US Service Center CN Service Center
USA China
Balluff Inc. Balluff (Shanghai) trading Co., ltd.
8125 Holton Drive Room 1006, Pujian Rd. 145.
Florence, KY 41042 Shanghai, 200127, P.R. China
Phone (859) 727-2200 Phone +86 (21) 5089 9970
Toll-free 1-800-543-8390 Fax +86 (21) 5089 9975
Fax (859) 727-4823 service@balluff.com.cn
technicalsupport@balluff.com
english 4