Connecting With Ios Devices; Adjusting The Input Sound; Mic Preamp Mode; Troubleshooting - Tascam US-16x08 Bedienungsanleitung

Connecting with iOS devices

You will need a Lightning to USB Adapter.*
* You must obtain a genuine Apple Lightning to USB Adapter
separately.

Adjusting the input sound

Analog audio signals input into this unit from mics, guitars,
keyboards and other audio equipment can be converted into
digital signals and transmitted to the computer via USB.
In addition, by connecting powered monitor speakers or
headphones to this unit, you can monitor audio signals.
Use the various controls as necessary.
Use the gain knobs ( ) to adjust the analog input levels
4
from the IN1-8 ( ) or IN9-10 (
1
indicators ( ) from lighting.
3
To listen to the monitoring signal using headphones, connect
headphones to the PHONES jack (
knob ( 6 ).
NOTE
If you cannot hear the input sound, make the following
adjustments.
• Use the PHONES knob on the front of the unit to adjust the
output level of the PHONES jack.
• Use the LINE OUT1-2 knob on the front of the unit to adjust
the output level of the LINE OUT1-2 jack.

Mic Preamp mode

This unit will operate in a mode called Mic Preamp mode when
it is not connected to a computer through a USB cable.
In this mode, you can use the unit as a standalone mic preamp
without using a computer or the like.
Input and output channels in Mic Preamp mode
In Mic Preamp mode, the mapping of the input channels to the
output channels is fixed as follows.
Input
IN1
IN2
IN3
IN4
IN5
IN6
IN7
IN8
You can adjust the output level of each channel using the gain
knob of the corresponding channel.
) jacks to keep the overload
2
) and adjust the PHONES
5
Output
LINE OUT1
LINE OUT2
LINE OUT3
LINE OUT4
LINE OUT5
LINE OUT6
LINE OUT7
LINE OUT8

Troubleshooting

Please read this chapter if you are unable to use the unit
properly even after setting it up following the procedures in this
manual.
If you are still unable to resolve your problems please contact
the store where you bought the unit or TEAC customer
support with the following information about the operating
environment and details about the trouble.
Operating environment
• Computer manufacturer
• Model
• CPU
• Memory (RAM)
• Operating system
• Applications used
• Antivirus software
• Wireless LAN use
See the end of this document for contact information.
Installation fails.
Installation completes, but the computer does not recognize
the unit.
If some trouble is causing installation to fail, or if the computer
does not recognize the unit even though installation completes,
check the following.
1. Change the USB port
Since the unit might not properly function with some
USB ports, try connecting to a different USB port on the
computer, and reinstall the driver.
NOTE
• Try again after disconnecting other USB devices. (Keyboards
and mice can be left connected.)
• Do not use a USB hub. Always connect the unit directly to a
USB port on the computer. (built-in)
2. Stop software that is running in the background
Since antivirus software and other software running in the
background can interfere with installation, stop them before
beginning installation.
See "Installing the dedicated software" on page 7 for how
to install and uninstall the dedicated software.
There is no sound even when audio is playing back.
The audio output must be set on the computer.
Please confirm the following while the unit is connected to the
computer. Moreover, if you make the following settings, sound
will be output through this unit, but no sound will be output by
the computer's speakers or headphone jack.
Windows 8/Windows 7
i See the "Windows 8" or "Windows 7" instructions in the
"Windows Media Player" section of "Application guide" in the
Reference Manual, and make settings as necessary for the OS.
i Conduct procedures 1–4 for Windows 8 or procedures 1–3 for
Windows 7 to set the default device for playback.
13
TASCAM US-16x08