Installation; Operation; Troubleshooting; Maintenance And Cleaning - Pentatech DP601 Bedienungsanleitung

Installation

Tip! mount the outdoor unit at a comfortable height for visitors to use.
Outdoor unit
!
Make a recess in the wall of approx. 110 x 17 x 4 mm (w x h x d) at the
required installation position for the outdoor unit. It is important that
the recess is not too large, as this would make it difficult to secure the
outdoor unit. Make sure that the twin-core cable is inside the wall
recess.
!
Fit the flush mount box [19] exactly into the wall recess. Make sure that
the front outer edge of the flush mount box is flush with the surface of the
wall (fixing clip [22] at the bottom). If necessary, fill any spaces
between the wall recess and the flush mount box with silicone.
!
Place the housing [14] of the outdoor unit onto the flush mount box
with the top edge on the retaining screw 2
!
Push the housing [14] up to the stop in the flush mount box (see Fig.D-
2).
!
Press the housing [14] tightly onto the fixing clip [22] of the flush mount
box (see Fig. D-3) and screw it in place with the retaining screw 1 [23]
(see Fig. D-4).
Indoor unit (see Fig. B)
!
Mark the screw openings [13] in the mounting plate [10] at the
installation position.
!
Fasten the mounting plate as required with the fastening screws and the
wall plugs onto the flat surface in the chosen installation position. Make
sure that the fastening lugs [11] (4 x) are pointing away from the
surface.
!
Push the indoor unit with the connected cable (optionally two) from
above onto the fastening lugs [11]
down until it clicks in place.
Name plate window
!
Carefully push the lefthand side of the name plate window
and then to the left.
!
Open the name plate window and remove the name insert.
!
Write your name on the insert and replace it behind the name plate
window.
!
Close the name plate window inwards and push it to the right until it
clicks in place.
Door release (optional)
!
To install a 12 V DC door release, follow the instructions and information
provided in the operating manual for the door release.
Power supply
!
Push the plug of the mains cable [5] completely into a mains socket. The
two red LEDs behind the name insert on the name plate window [17]
light up. If the two red LEDs do not light up, the connection between the
indoor unit and the outdoor unit has not been made properly.
!
Connect the indoor unit and the outdoor unit properly. The door intercom
is now ready for operation.
GB - 16
[20] (see Fig. D-1).
of the mounting plate. Then push it
[17] inwards

Operation

A visitor presses the bell button [16] on the outdoor unit. The two red LEDs
behind the name insert on the name plate window are not illuminated for as
long as the bell button remains pressed. A two-tone signal rings twice on the
indoor unit. If the visitor holds the bell button r down longer, the ring tone
occurs a corresponding number of times.
!
Remove the receiver [2] from the indoor unit.
!
Speak to the visitor into the bottom part (mouthpiece) of the receiver.
The visitor can hear you through the loudspeaker [15] and answers with
the aid of the microphone [18] on the outdoor unit.
!
You can hear the visitor through the upper part (earpiece) of the receiver.
!
When you have finished your conversation, replace the receiver.
Door release (optional)
!
If a door release is connected, you can unlock the door / the gate in the
following way:
Door release with latching function
A door release with latching function is unlocked when the signal is given.
!
Press the door release button E. The gate or the door is locked once it has
been opened and closed again.
Door release without latching function
!
Keep the door release button E pressed until the visitor has opened the
door. It is possible to open the door during the time in which you are
pressing the door release button.
!
When you let go of the door release button, the door is locked
immediately. It is also possible to unlock the door / the gate when the
receiver is hooked up on the indoor unit.

Troubleshooting

Fault Cause
The door intercom is not working or is not working
properly...
The cable between the indoor unit and outdoor unit is faulty. The two red
LEDs behind the name plate window t do not light up.
Correct the fault in the cable. Observe the polarity marking on the cable.
The sound of the visitor's voice is weak.
The visitor is standing too far away from the outdoor unit.
Ask the visitor to move closer to the outdoor unit.

Maintenance and cleaning

!
Disconnect the indoor unit from the power supply before maintenance
and cleaning.
!
Check the technical safety and function of the device regularly.
!
Use a soft cloth and a mild agent, if necessary mild soap suds, to clean
the plastic and metallic surfaces.
!
Never use solvents, thinner or similar chemical substances.
!
Remove deposits of dust from the air vents with a brush or use a vacuum
cleaner at min. 5 cm distance from the components.
Remedy