Special Features; Problem Solving; Ec Declaration Of Conformity - Summer baby wave deluxe Bedienungsanleitung

S ET UP & USE:
Initial Set Up:
To set up the system, you will need two adults. One adult should be in the
nursery with the Baby Unit (transmitter) while the other is in a different
room with the Parent Unit (receiver).
Note: The Parent Unit includes a rechargeable battery and it should be
fully charged before using the monitor in portable mode. Charge the
battery for 12-16 hours. When the unit is fully charged, the LED under the
On/Off switch will remain on until it is unplugged. After the initial 12-16
hour charge, only charge the battery when the battery is low to achieve
optimal battery life.
Step 1: Place the Baby Unit in the nursery near the cot, on a flat surface,
and ensure the cord is more than 1 metre from the cot and out of baby's
reach. Plug the AC adapter into a standard electrical outlet.
Step 2: Press the power button on the front of Baby Unit for 4 seconds to turn the unit on.
Step 3: Place the Parent Unit in the room from which you want to monitor baby. Plug the AC adapter into a
standard electrical outlet.
Step 4: Press the power button the front of the Parent Unit for
4 seconds to turn it on.
Step 5: Have the adult in the baby's room speak at different levels to adjust the volume to the desired setting. The
volume can be adjusted up or down using the Volume Control buttons on the side of the Parent Unit.
Baby Unit Set Up in Nursery:
Place the Baby Unit (transmitter) on a flat surface, such as a desk or shelf (Fig A). NEVER place the Baby Unit or cords
within 1 metre of the cot.
Synchronizing Baby and Parent Unit:
Note: This digital monitor set is synchronized with security codes for privacy reasons. However, there are instances
that the Baby and Parent unit will lose it's code and may require you to synchronize it again.
Step 1: Connect the Baby unit to it's power supply and make sure unit is powered OFF.
Step 2: Turn ON Parent unit.
Step 3: Press and keep holding the "VOL +" button and at the same time press the POWER button for about 4
seconds. A continuous audible BEEP and red flashing lights will occur. The Parent unit is now ready to be synchronized.
Step 4: Within 20 seconds, turn on the Baby unit. A single BEEP will emit from the Parent unit to signify successful
synchronization.
Battery Installation:
Note: this step is only needed if replacing battery.
1. Locate the battery compartment door on the back of Parent Unit
2. Slide battery door off
3. Remove battery
4. Insert new battery and replace battery door.
S PEC IAL FEAT UR ES:
• Two-way Communication: To speak to your baby, press the Talk Back button on the side of the parent unit
while speaking into the microphone on the front of Parent Unit.
• Nightlight: To activate night light, press the Nightlight On/Off button on the side of the parent unit.
• Temperature Monitoring: Press and hold the nightlight button for 4 seconds to switch between Fahrenheit
and Celsius.
• Sound Lights: The colour of the sound lights changes, moving from green to amber to red as the sound level
increases.
• Out of Range Indicator: If the Parent Unit is too far away from the Baby Unit, it will be "out of range" and the
monitor (parent unit) will emit 4 consecutive beeps. The beeps will continue until the Parent Unit is moved back
A
within range of the Baby Unit.
• Low Battery Indicator: If the Parent Unit is low on battery power, the unit will emit a beeping sound. The low
battery will continue to beep until the unit is plugged in.
PROB LE M SO LVI NG :
No sound coming from the speaker
• Make sure both the Baby Unit and Parent Unit are plugged in and powered on.
• Make sure electrical outlets are working.
• Set volume to a higher setting.
Static
• Move the Parent Unit closer to the Baby Unit.
Squealing Noise
• Move the Parent Unit and Baby Unit farther apart, the squealing sound indicates the units are too close together.
• Turn down the volume on Parent Unit.
Weak reception or no reception
• Make sure both Parent Unit and Baby Unit are turned on.
• Move the Parent Unit closer to the Baby Unit.
• Make sure the battery in the Parent Unit is fully charged.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the 28916 Digital Audio Monitor is in conformity with the standards
ETSI EN 300 328, ETSI EN 301 489-17, ETSI EN 489-1 and EN 60950-1, and is compliant with the essential
requirements and other relevant provisions of Directives 1995/5/EC and 2006/95/EC.
Summer Infant, Inc.
1275 Park East Drive
Woonsocket, RI 02895 USA
1-800-268-6237
© 2013 Summer Infant, Inc
John Anson
Head of New Product Development
1st August 2013
Summer Infant Europe, LTD.
First Floor, North Wing
Focus 31, Cleveland Road
Hemel Hempstead, HP2 7BW UK
+44 (0) 1442 505000
customerserviceuk@summerinfant.com
06/14