Yamaha PDM-4220 Bedienungsanleitung Seite 25

OPERATING INSTRUCTIONS (continued)
Displaying MULTI PICTURE (continued)
Activating the Split mode from the video input screen
Pressing the MULTI PICTURE button one time will display 2 pictures.
• The speaker icon can be shifted left and right by pressing the
the video will be output from the side on which the speaker icon is located.
• The same video input mode cannot be selected for both screens at the same time.
• Pressing the MULTI PICTURE button again will cancel the 2 pictures display.
• Refer to the table for 2 pictures (Split) mode.
Activating the MULTI PICTURE mode from the RGB input screen
Pressing the MULTI PICTURE button one time will display 2 pictures.
• This mode can be available from RGB1(DVI-PC) and RGB2(RGB) input.
• The speaker icon can be shifted up and down by pressing the
be output from the side on which the speaker icon is located.
• The sub-screen position can be selected up and down by pressing
• The sub-screen can be selected with the AV1
icon appears on the left side of AV✱ etc. as shown in the diagram to the right.
• Pressing the MULTI PICTURE button again will cancel the 2 pictures display.
• "Frequency Mode" in the Setup Menu should be set to Movie when sub-screen is the component signal of
1080i/50 or 1080i/60.
NOTE
• Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the multi picture display, the mode will not change
to power save mode.
• Please be careful since image retention will occur if display is left in a multi picture display state for a long period of time.
2 pictures (Split)
Input terminal
Sub
TV
Main
TV
‡
PAL , SECAM
AV1
~AV5
‡
NTSC3.58/4.43
AV2
RGB
‡
AV3
576i, 576p ‡
‡
480i, 480p
‡
1080i/50
AV1
AV2
‡
1080i/60
720p/50
‡
720p/60
RGB1
STB
RGB2 ‡
Component
4 pictures
Input terminal
Sub
TV
Main
TV
‡
PAL , SECAM
AV1
~AV5
‡
NTSC3.58/4.43
AV2
RGB
‡
AV3
‡
576i, 576p
‡
480i, 480p
‡
1080i/50
AV4
AV6
‡
1080i/60
720p/50
‡
720p/60
RGB1 STB
‡
RGB2 Component
NOTE
About 720p/50Hz
• 720p/50Hz can support for AV4, AV6, and RGB 1 (DVI-STB) only during the single picture mode.
• RGB2 (component) is not available for 720p/50Hz.
24
AV6, TV channel buttons from the status that the speaker
~
AV1~AV5 AV2, AV3
PAL NTSC3.58 576i
RGB
SECAM NTSC4.43 576p
‡ ‡ ‡
‡
‡
‡ ‡
‡
‡ ‡ ‡
‡
‡ ‡ ‡
‡
‡ ‡ ‡
‡
‡ ‡ ‡
‡
‡ ‡
‡ ‡
‡ ‡ ‡
‡
‡
‡ ‡
‡
‡ ‡ ‡
‡
AV1~AV5 AV2, AV3
PAL NTSC3.58 576i
RGB
SECAM NTSC4.43 576p
‡ ‡
‡
‡ ‡
‡
‡ ‡
‡
‡
‡ ‡
‡ ‡
‡
‡ ‡
‡
‡ ‡
‡
‡ ‡
‡
‡ ‡
‡
‡
‡ ‡
and SELECT buttons. The audio of
and SELECT buttons. The audio will
and SELECT buttons.
AV1: Displays the VIDEO input signal of the sub-screen.
AV4, AV6
480i 1080i/ 1080i/ 720p/ 720p/
480p 50 60 50 60
‡ ‡ ‡ ‡
‡ ‡ ‡ ‡
‡ ‡ ‡ ‡
‡ ‡ ‡ ‡
‡ ‡ ‡ ‡
‡ ‡ ‡ ‡
‡ ‡ ‡ ‡
‡ ‡ ‡ ‡
‡ ‡ ‡ ‡
‡ ‡ ‡ ‡
AV4, AV6
480i 1080i/ 1080i/ 720p/ 720p/
480p 50 60 50 60
AV1
RGB2
AV1
RGB1 RGB2
TELE
STB Component TEXT
Main
‡
(‡ : available)
RGB1 RGB2
TELE
STB Component TEXT
Main
(‡ : available)
AV2
(Sub-
screen)
Sub
Sub 1
Sub 2
Sub 3