Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Manual: Pure Micro Series
1. Scope of delivery & details
Please check if all listed parts are included and undamaged. Included in delivery:
1 x laser projector
1 x external PSU
1 x manual
1x Allen key 4mm
2. Preliminary warning notices
1. Please use this device only according to these operating instructions.
2. Do not use the device if there are any visible damages on housing, connector panels,
power supplies or power cords.
3. Never look directly into the light source of a laser projector. Danger of blindness!
4. Do not operate the device at high humidity or in the rain.
5. Protect device against dripping or splashing water. Do not place any liquid filled
containers at the device.
Warranty claim expires with removal of warranty label.
3. Initial operations, safety instructions
1. Make sure to use correct voltage; see in-
formation on device & in this manual.
2. Make sure that the device is not connec-
ted to mains during installation.
3. Installation has to be done by technical
experienced and qualified persons ac-
cording to safety regulations of the res-
pective country.
4. Always ensure that maximum permissib-
le exposure (MPE) is not exceeded in are-
as accessible to the public.
5. In some countries an additional
pection by technical control institutes
could be necessary.
6. Connect an easily accessible inter-
lock connector or circuit breaker
to the projector.
page 4 / 20
7. The power supply should be easily acces-
sible.
8. When installing the laser mount it with
a minimum distance of 15 cm from walls
and objects.
9. For safe setup e.g. on walls or ceilings
please use a safety cord. The safety cord
should be able to withstand tenfold the
weight of the device. Please follow the
accident prevention regulations of pro-
fessional associations and/or comparable
regulations for accident prevention.
ins-
10. If the device has been exposed to great
temperature changes, do not switch it
on immediately.
11. Never use dimmer, RC or other electroni-
cally switched sockets. Whenever possib-
le, do not use the laser projector together
with large appliances (especially fog ma-
chines) on the same mains!
12. Ensure sufficient ventilation and do not
place the device on any warm or heat ra-
diating surface. Especially the ventilati-
on openings must not be covered!
13. Ensure that device does not get over-
4. Working on the device
1. Be sure that the mains plug is not connected to the power sup-
ply while installing the device.
2. Take off all reflecting things like rings, watches etc. before
starting to work with or at the projector.
3. Only use non-reflecting tools to work on device.
4. Wear protective clothing (like goggles, gloves etc.) accor-
ding to laser power and wavelength of the laser.
5. Service notes
•
Moisture and heat can reduce lifetime of
the laser system dramatically and expires
any warranty claim.
•
Quick on/off switching of device can re-
duce durability of the laser diode drama-
tically.
•
Avoid concussions during transport.
•
To increase durability of your laser,
protect device against overheating:
-
Always ensure sufficient ventilation.
-
Do not face spotlights (especially mo-
ving heads) to the device.
-
Check temperature after approx. 30
minutes with each new installation.
If necessary install the projector at a
place with different temperature.
-
Keep the device dry. Protect it from
moisture, rain and damp.
Manual: Pure Micro Series
heated. Make sure that the device is not
exposed to spotlights (especially moving
heads). Heat of spotlights could overheat
laser in a little while and leads to a degra-
dation of performance.
-
Switch off device when it is not nee-
ded. Diodes are switched on and can
wear off even if there is no visible la-
ser output.
•
As for troubleshooting, please check the
FAQ on our website www.laserworld.com
• Removal of the warranty label as well
as damages to the device caused by
improper handling, neglect of the sa-
fety instructions and service notes will
void the warranty.
•
As for troubleshooting, please check the
FAQ on our website www.laserworld.com
• Removal of the warranty label as well
as damages to the device caused by
improper handling, neglect of the sa-
fety instructions and service notes will
void the warranty.
page 5 / 20
Werbung
