Installation - tzs First AUSTRIA FA-5571-7 Bedienungsanleitung

INSTRUCTION MANUAL
WALL MOUNTED PTC FAN HEATER USAGE GUIDANCE
• Please read this guidance carefully before using your wall mounted PTC heater, so that you
can use it correctly.
• Please keep well with this guidance.
BRIEF INTRODUCTION OF THE PRODUCT
PTC heater has a heating and fan function in the same machine, and it looks like an air
conditioner with latest design. With remote control make it to be operated easily and safely, the
machine adopts PTC heating material heating it quickly, it's durable and without flame.
FEATURE:
• PTC ceramic heater elements, high efficiency heating, quickly heating, noise-less odor-
free, non-polluting, no flame and will not killing the oxygen
• Wall mounted
• Cool,warm or hot wind
• Automatic oscillating louvers
• LCD
• 8 hours timer
• Remote control
• Overheat protection
NOTES:
1. The heater should be hung on the wall and the wind outlet should face down or be placed
on flat appliance. You must not place it precipitantly or tipsily.
2. Please do not use the heater in places full of combustible or explosive gas. Don't cover the
wind outlet.
3. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent
or a similarly qualified person in order to avoid a hazard
4. If nobody is in or you are repairing the heater, please disconnect the heater from electric outlet.
5. Please don't touch the heater with wet hands or other conductors.
6. Motor is out of order, please make it stop immediately.
7. During use, please do not open the door or window otherwise it will diminish the heating
effect.
8. To turn off the machine, press the on/off switch to off, then the machine will keep the fan
working about 30 seconds until it blows out cool wind, then the machine will stop working
and you can take out the plug.
9. Must hang the heater on the wall and fix it away from water in bathroom.
10. Remote control, please use AAA battery, matched with the heater, heater panel LCD
display room temperature.
11. If the product needs repair, please ask experts or our company authorized maintenance
department.
WARNING:
Don't touch the working machine and don't cover the wind outlet and inlet!
m_5571-7-8_v02.indd 2-3 m_5571-7-8_v02.indd 2-3
2
NAME OF THE COMPONENTS
(see picture 1):
1) COVER
2) WIND INLET
3) WIND OUTLET
4) FANNER
5) BASE
6) CONTROL PANEL

INSTALLATION

(see picture 2):
Drill two holes into the wall and keep a distance of 1.8m from the ground. The diameter of the
hole just contains the inflated plastic pipe. After tucking the inflated plastic pipe, fix pothook on
the pipe with screws. Make sure pothook are safely placed and hang the heater. The clip under
the pothook should be inserted rabbet of the heater bottom.
CLEANING AND MAINTENANCE
1. If you don't use the heater for a long time, please wipe the surface and put it into the box.
Lay the carton on a ventilated and dry place. Humidity and pressure on the carton can
damage your product.
2. Wait for the machine to cool down before pulling out the plug, then clean it. Wipe it clean
with a wet washcloth or cleaner. Never directly wash with water, do not drop water into the
machine. Never clean with acids, chemical thinner, gasoline, benzene etc.
3. Before every use, please check to make sure that the outlet ventilation has no sundries.
FUNCTION INSTRUCTION
MACHINE PANEL
Plug cord into the electric outlet, press " ", wind window will open and blow out natural wind.
Secondly press " " is Power off, and the blue light shining, 30 seconds later, it will stop working
automaticly.
When heater on working, press first time is 1000W, second time is 2000W. It is circle use.
When heater on working, press this button. The fin will automatic swing up and down.
◴
Setting the heater working hours.
1h – 2.0h – 3.0h – 4.0h – 5.0h – 6.0h – 7.0h – 8.0h
3
2010.5.17 6:04:19 PM 2010.5.17 6:04:19 PM