Schuller Ehklar EASYSAND DUO600 Gebrauchsanweisung Seite 10

GB
i) Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective
equipment. Fragments of the workpiece or of a broken accessory may fly away and cause injury beyond the immediate area
of operation.
j) Hold power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may
contact hidden wiring or its own cord. A cutting accessory contacting a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an electric shock.
k) Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or
arm may be pulled into the spinning accessory.
l ) Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the
surface and pull the power tool out of your control.
m) Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your
clothing, pulling the accessory into your body.
n) Regularly clean the power tool's air vents. The motor's fan will draw the dust inside the housing and excessive accumulation
of powdered metal may cause electrical hazards.
o) Do not operate the power tool near flammable materials. Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or
shock.
2) KICKBACK AND RELATED WARNINGS
• Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory.Pinching
or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in
the direction opposite of the accessory's rotation at the point of the binding.
• For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the
pinch point can dig into the surface of the material causing the wheel to climb out or kick out. The wheel may either jump
toward or away from the operator, depending on the direction of the wheel's movement at the point of pinching. Abrasive
wheels may also break under these conditions.
• Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a) Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use
auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control
torque reactions or kickback forces, if proper precautions are taken.
b) Never place your hand near the rotating accessory. The accessory may kickback over your hand.
c) Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in the
direction opposite to the wheel's movement at the point of snagging.
d) Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback.
OPERATING / USE
SHAFT (PICTURE 2)
• Fold the front and back part together (2a).
• Push the folding lock H to the right position and keep the tip adjacent to the handle .(2b)
• Press the folding lock H towards the handle until the end. (2c) Unfold the handle by pushing the folding lock to the inside.
REPLACE SANDING PAD (PICTURE 3)
• Insert the hex wrench (size 5) into the hexagonal screw bolt on the sanding block
• Hold the sanding pad firmly, and then turn the wrench counter clockwise to dismount the pad.
• Install new sanding pad by tightening the bolt.
Warnning: Only install the specified sanding pad on the machine.
ROUND HEAD AND TRIANGLE HEAD EXCHANGE (PICTURE 4)
• Operate the lock lever F to the left to remove the head
• Remove the head (1 / 2)and connect the motor housing G and big bearing cove to the put the head what you want to use
on the machine
• Slide the lock lever F into lock position to lock the new head.
Warnning: Only install the specified sanding pad on the machine. In order to ensure optimal performance, the machine
should be run at slightly lower speed for several minutes to make the grinding pad fit the sealing surface perfectly. During this
process, the white foam particles will come out from the sanding head. However, this won't damage the machine.
www.schuller.eu
10