Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
WARNING Injury
!
Never operate this appli-
ance...
- in rooms where the appliance is
at risk of fire or explosion as a re-
sult of chemicals, dust, gases or
vapours.
- in the direct proximity of elec-
trical cables or receptacles that
carry or contain flammable or
explosive materials.
- if work such as laying tiles, san-
ding or sealing is being carried
out in the installation room.
- if naphtha sprays, floor polish or
similar products are used. Venti-
late the room sufficiently before
heating.
- if the minimum clearances to
adjacent surfaces are not main-
tained.
- if the power cable shows signs of
damage.
WARNING Burns
Never place any flammab-
le, combustible or insu-
lating objects or materials, such
as laundry, blankets, magazines,
containers with floor polish or
naphtha, spray cans or similar on
the appliance or in direct proxi-
mity to it.
WARNING Electrocution
- Never touch any live com-
ponents.
- Do not operate the device when
your hands are wet.
- Never operate the appliance in
the immediate vicinity of a bath
tub, a shower or a swimming
pool.
- Position the appliance in such a
way that the control mechanisms
cannot be touched by a person in
the bath or shower.
CAUTION Burns
Never cover the appliance.
CAUTION Burns
Parts of the appliance can
get very hot and may cause
burns. Particular caution is advi-
sed when children or vulnerable
persons are present.
CAUTION Injury
!
Never step on the appli-
ance.
Material losses
!
- Never cover the power
cable with a carpet or rug.
- Make sure that the power cable is
not in anyone's way, and that no
one can trip over it and tip over the
appliance.
- Avoid using an extension cable.
If required, use only undamaged,
tested extension cables suitable
for the power consumption of the
appliance.
- Position the appliance on a solid
base. On a soft base, the applian-
ce can tip over or the air apertures
can become blocked.
- Never move or carry the appliance
by pulling on the power cable.
- Do not wind the power cable
around the appliance when it is in
operation.
- Do not pull the power cable across
sharp edges.
Note
Never operate the applian-
ce remotely or have it swit-
ched on automatically via upstre-
am components (e.g. time switch,
room temperature controller).
2.3 CE designation
The CE designation certifies that the
appliance meets all essential require-
ments according to the:
-
Electromagnetic Compatibility
Directive
-
Low Voltage Directive
2.4 Test symbols
See type plate on the appliance.
3. Appliance descrip-
tion
The appliance is an electric direct
heater and is suitable as e.g. a full
heating system in bathrooms, or for
use between seasons and as a boos-
ter heater in smaller rooms.
For heating, the indoor air is drawn
in by the appliance fan via apertu-
res in the back panel, heated by the
heating element, and blown out for-
wards via the air outlet grille.
3.1 Anti-tipping protection
To prevent the possibility of fire, the
appliance features automatic an-
ti-tipping protection.
If the appliance tips forwards or
backwards, it switches off automati-
cally. When the appliance is returned
to a normal, upright position, it auto-
matically switches back on.
4. Settings
Operating selector
You can use the operating selector
to switch the appliance on and off,
and to select the desired operating
mode.
Symbol Operating
Meaning
mode
0
Zero setting Appliance
switched
off
Fan
Cold stage
Fan opera-
tion only
1
Heating
900 W hea-
stage 1
ting output
2
Heating
1800 W
stage 2
heating
output
4.1 Temperature selector
The temperature selector serves to
set the required room temperature.
When the room temperature falls
below the set value, the appliance
begins to heat.
To get the room temperature
which is right for you ...
f Set the operating selector to
f
heating stage 2.
f Turn the temperature selector
f
fully clockwise (maximum
value).
The appliance starts heating.
f When the room temperature re-
f
aches a level that feels pleasant
to you, turn the temperature
selector back until the appliance
switches off with an audible
click.
The appliance will keep the room
temperature constant at the set
value by repeated short periods of
heating.
4.2 Frost protection
The appliance is equipped with a
frost protection function, which swit-
ches the appliance on automatically
if the room temperature falls below
approx. 7 °C.
To activate the frost protection
function ...
f Turn the temperature selec-
f
tor fully anti-clockwise to the
snowflake symbol (minimum
value).
f Set the operating selector to he-
f
ating stage 1 or heating stage 2.
5. Cleaning, care and
maintenance
The appliance contains no user ser-
viceable parts.
f Clean the appliance when cold
f
with ordinary cleaning products.
Avoid abrasive or corrosive clea-
ning products.
f If a pale brownish discolouration
f
appears on the appliance casing,
wipe it off with a damp cloth.
f Clean the air inlet and outlet
f
grilles twice a year with a vacu-
um cleaner.
Material losses
!
Never spray cleaning spray
into the air slot.
6. Storage
f If you will not be using the appli-
f
ance for a long period, switch it
off and unplug it.
f When not in use, keep the appli-
f
ance in a dry place.
7.
Troubleshooting
If the appliance does not heat, check
the temperature set at the appliance
and the MCB/fuse in your fuse box.
The appliance is equipped with a saf-
ety temperature controller that shuts
the appliance down if it overheats.
After the cause has been remo-
ved (for example air outlet or inlet
apertures covered) and the appliance
has cooled down for a few minutes,
operation starts again.
If you cannot remedy the fault, notify
your qualified contractor. To facilitate
and speed up your request, provide
the number from the type plate
(000000-0000-000000).
INSTALLATION
8. Safety
Only a qualified contractor should
carry out installation, commissio-
ning, maintenance and repair of the
appliance.
8.1 General safety instruc-
tions
We guarantee trouble-free function
and operational reliability only if
original accessories and spare parts
intended for the appliance are used.
8.2 Instructions, standards
and regulations
Note
Observe all applicable na-
tional and regional regula-
tions and instructions.
9. Installation location
-
There must be at least 90 cm
clearance between the applian-
ce and any combustible objects
(e.g. curtains), walls or other
building elements.
-
Never operate the appliance on
deep-pile carpets.
-
Never operate the appliance on
unstable or uneven surfaces.
-
Never position the appliance
directly below a wall socket.
-
Never operate the appliance in
the open air.
10. Power supply
Material losses
!
Observe the type plate.
The specified voltage must
match the mains voltage.
Material losses
!
This appliance is not suita-
ble for hardwired connec-
tion.
Note
The power cable must only
be replaced by a qualified
contractor using original spare
parts supplied by us.
| 9
Werbung
Inhaltsverzeichnis
