Instruction Manual - Dennerle Trocal LED Control Bedienungsanleitung

EN
1
Congratulations on purchasing this high-end Dennerle product. We wish you years of enjoyment and pleasure with your aquarium!
- Please read all instructions carefully before turning the equipment on. Save these instructions for future reference. -
Please read these instructions in full before connecting or setting the device. Once you understand the basic operating concept, it will be easier for you to quickly
and appropriately set the Dennerle Trocal LED Control (from here on referred to simply as LED Control).
Safety notes
• The device may only be operated with the corresponding Dennerle components (power supply, lights). Take note of the appropriate operating instructions and
the safety notes for the peripheral devices.
• Unplug the device before performing any maintenance or installing the light.
• Only for direct current 12-24 V
• The maximum current-carrying capacity per output is 2.5 A and must not be exceeded.
• For indoor use only.
• Always disconnect all equipment in the water from the power supply before reaching into the aquarium.
• The mains plug must be accessible at all times after installing the device.
• Cables leading from the aquarium must be fitted with a drip loop so that any water running down cannot reach the equipment or the mains socket.
• If a cable or the mains adapter becomes damaged, then the device must no longer be used. Damaged cables or mains adapters must be replaced. Only genuine
Dennerle replacement parts may be used. Contact your specialist retailer or Dennerle Customer Service.
• This equipment is not intended to be used by persons (including children) with limited physical, sensory or mental capacity, lack of experience, and/or lack of
knowledge, unless said persons are supervised for their own safety by another responsible person or are given instructions by this person on how to use the
equipment. Children must be supervised to ensure that they do not play with the equipment.
• Do not expose or cover LED Control and mains adapter; always ensure a good level of cooling.
• The device must not be mounted on or in the cover frame.
• The LED control must be mounted outside of the wet area.
• This product must not be disposed of in normal household waste, and should be disposed of at your local refuse centre.
Function keys, connections and components
A
Graphics display: Basic setting displays: Date, time, current illumination

intensity in %, moon phase
LED: lights green during saving test or when the PC is connected to the
2
socket position no .

Cursor keys::  Go up a menu level or increase an entry value
3
 Go down a menu level or reduce an entry value
 M ove right
 M ove left
 Escape (back key) or cancel an action
4
Return (confirm) or continue

5
Input for mains adapter for light 1
6
Input for mains adapter for light 2
7
Output for light 1
8
Output for light 2
9
USB connection to upload software updates, parameterize all user data,

such as setting the illumination curves .
12
Instruction manual for
Dennerle Trocal LED Control
English translation of the original German operating instructions
Connection the lights
A
Connect the:
1 . Trocal LED 1 with output no .
8
2 . Trocal LED 2 with output no .
9
3 . the LED Connect cable no . B with input no .
4 . the other end of LED Connect cable (at input no .
ding mains adapter for the Trocal LED no . 1
5. a second LED Connect cable (accessory item 5549) with the input no.
(option for 2 lights)
6 . the other end of LED Connect cable (at the input no .
ponding mains adapter for the Trocal LED no . 2
Caution! When operating Trocal LEDs with different power on one LED
Control, under no circumstances should the power adapters be swapped .
7 . the power adapters each with a mains socket .
Connection to PC:
To carry out software updates or to programme via PC software.
1. I nstall GHL Control Center (GCC) on your PC (download link see www.
dennerle . c om) .
2. Open GHL Control Center.
3 . Connect the LED Connect cable no . B with input no .
4 . Connect the other end of LED Connect cable (at the input no .
corresponding mains adapter for the Trocal LED no . 1
5. Plug the mains adapter into a main socket
6. Using the USB cable no. C connect it to your PC
7. Open the program GHL Control Center on your PC (see current advice at
www . d ennerle . c om)
8. With the help of the GHL Control Center, you will now be able to adjust the
settings on the LED Control
(option for 2 lights)
6
) with the correspon-
6
) with the corres-
7
6
) with the
6
7