Installation - Renkforce 1390555 Bedienungsanleitung

Operating instructions
GoPro Microphone
Item no. 1390555
Intended use
The product is intended to work with a GoPro camera. The microphone can catch
a wide range of background sound to be reproduced in good quality, making your
video impressive by enriching the background sound. Power is supplied by the GoPro
camera.
Contact with moisture, e.g. in bathrooms, must be avoided under all circumstances.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting,
fire, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• Microphone
• Wind screen
• Three-part bracket
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Do not place the product under any mechanical stress.
• When setting up the product, make sure that the cable is not pinched,
kinked or damaged by sharp edges.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, flammable gases, vapours and solvents.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• The complete product must not become wet or damp. Never touch the
product with wet hands.
• Also observe the safety and operating instructions of any other devices
which are connected to the product.
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Operating elements
The GoPro frame with its base and screws shown in the figures below are
not supplied.
6
2

Installation

Do not overtighten the screws, as this may cause damage to the product
and/or the GoPro frame.
a) Mounting the bracket to the GoPro frame
GoPro frame with base
and screw (not supplied)
• Remove the screw of the GoPro frame to separate the frame and its base.
Bracket
Supplied long screw
Screw of GoPro frame
• Fit the GoPro frame, the bracket and the GoPro frame base together.
• Secure with the supplied long screw and the screw of the GoPro frame.
b) Mounting the microphone and adjusting the distance between GoPro
and the microphone
Microphone
Supplied short screw
• Put the microphone onto the bracket. Secure with the supplied short screw.
• To adjust the distance between the microphone and the GoPro frame, unscrew the
short screw and relocate the microphone along the bracket. Then secure with the
short screw.
c) Setting up the microphone
• Connect the mini-B USB cable to the mini-B USB socket of GoPro.
• Optionally, cover the microphone capsules with the wind screen.
• Set the HI/LO switch on the back of the microphone as desired when recording.
5
4
1 Bracket
2 Long screw
3 Short screw
4 Microphone
5 HI/LO switch
6 Mini-B USB cable
1 3
GoPro frame base
GoPro
frame
Screw of GoPro
frame base