TFA 60.2012 Bedienungsanleitung Seite 6

TFA_No. 60.2012 Anleitung 19.11.2012
TIME BLOCK
– Digital alarm clock
• Do not use the unit if the housing or the main adapter is damaged.
• Keep the unit out of reach of persons (including children) who cannot fully appreciate
the potential risks of handling electrical equipment.
• Pull the plug out of the socket immediately if any fault occurs or if the unit is not used for
a lengthy period.
• Only use the supplied mains adapter.
• Do not pull the plug out of the socket by its lead.
• Route the mains lead so that it does not come into contact with sharp-edged or hot
objects.
Caution!
Risk of injury:
• Keep the battery out of reach of children.
• Batteries must not be thrown into the fire, short-circuited, taken apart or recharged. Risk
of explosion!
• Batteries can be fatal if swallowed. If a battery has been swallowed, get medical assis-
tance immediately.
• Batteries contain harmful acids. Low batteries should be changed as soon as possible to
prevent damage caused by a leaking battery.
• Wear chemical-resistant protective gloves and glasses when handling leaked batteries.
Important information on product safety!
• Do not place the unit near extreme temperatures, vibration or shockshock.
• Do not place any objects on the instrument.
5. Elements and buttons
1. IR motion sensor
3. Alarm indicator
5. ALARM ON/OFF switch
7. RESET hole
9. Button cell compartment
11. MODE button
13. DOWN button
15. Button cell compartment cover
6. Getting started
• Open the battery compartment and remove the insulation strip.
• Insert the adapter into the jack. Connect the power adapter to a wall socket. Important!
Make sure that your household voltage is 230V! Otherwise your clock may be damaged.
• A short beep sounds.
• The alarm clock starts to run a test.
• Then 12:00 and PM appear on the display.
10
13:51 Uhr Seite 6
2. PM indicator
4. SNOOZE button
6. FUNCTION switch
8. DC Jack
10. Brightness adjusting switch
12. UP button
14. CR2032 button cell
16. Temperature sensor
TIME BLOCK
– Digital alarm clock
6.1 12/24 hours indication
• In normal mode, press DOWN button to select 12 (PM appears on the display after 12 h)
or 24 hour mode.
6.2 Setting of the clock and date
• Move the FUNCTION switch to 'T.SET' (TIME SET).
• The hour digits are flashing.
• Press UP or DOWN button to adjust the hours.
• Press MODE button and the setting sequence is shown as follows: Minutes, seconds, year,
month and day. Adjust with UP or DOWN button.
• Move the FUNCTION switch to 'NORMAL', the clock and calendar settings are finished.
6.3 Setting of the alarm time
• Move the FUNCTION switch to AL.SET (ALARM SET).
• The hour digit and AL start flashing.
• Press UP or DOWN button to adjust the hours.
• Press MODE button and the setting sequence is shown as follows: Minutes and the snooze
interval, the default setting is 5, (snooze-function from 1 minute to 60). Adjust with UP or
DOWN button.
• Move the FUNCTION switch to 'NORMAL'. The alarm setting is finished.
6.4 Activate/turn off Alarm ON/OFF
• Move the ALARM ON/OFF switch to AL ON (ALARM ON).
• AL appears on the display. The alarm is activated.
• When the alarm time is reached the wake-up signal sounds.
• Wave your hand within 2 inches distance to the motion sensor or press the SNOOZE but-
ton to activate snooze function.
• For the duration of the pre-set interval function, the alarm will be interrupted up to four
times.
• If there is no man-made stop, the clock will alarm lasting 1 minute every snooze interval,
four times totally.
• Press any button and the alarm will stop.
• Move the ALARM ON/OFF switch to 'AL.OFF' (ALARM OFF) to switch off the alarm func-
tion.
6.5 Temperature display
• By pressing the UP button the temperature unit can be changed from °C to °F in normal
mode.
6.6 Reading of the temperature, date, the alarm time and the snooze interval
• Press the SNOOZE button or wave your hand within 2 inches distance in normal mode to
show the temperature, the date, the alarm time and the snooze interval.
6.7 Brightness
• Move the brightness adjusting switch to change brightness in 3 steps (HIGH-MIDDLE-
LOW).
11