Conrad 86 04 02 Bedienungsanleitung Seite 4

Use with a cigarette lighter socket
The product is only suitable for vehicles that have a 12V power supply
or vehicles that provide a 12V power source via their cigarette lighter socket.
With any other voltages (e.g. 24Vdc) the product will be destroyed, the warranty will
be void!
Switch off the product, move the switch „WARM - STOP - COOL" into the position „STOP".
Move the switch „DC - STOP - AC" into the position „DC".
Connect the low-voltage socket (e.g. marked with „12V DC") to a suitable cigarette lighter socket
using the supplied 12V connection cable.
Never use force when inserting the low-voltage plug on the 12V connection cable into the pro-
duct's socket!
When connecting to a vehicle's cigarette lighter socket, please make sure that
extended use does not lead to total discharge of the vehicle battery.
In some vehicles, the ignition must be on in order to be able to use a device con-
nected to the cigarette lighter socket (see manual of your vehicle).
Operation via Mains Voltage
The product is suitable for connection to a mains voltage of 220-240V~, 50Hz.
With any other voltages, the product will be destroyed, the warranty will be void!
Switch off the product, move the switch „WARM - STOP - COOL" into the position „STOP".
Move the switch „DC - STOP - AC" into the position „AC".
Connect the socket (e.g. marked with 220/240V~) to an appropriate mains socket using the sup-
plied power cable.
Opening/closing the door
Opening the door:
Move the handle at the bottom carefully to the right, until the door can be opened.
Closing the door:
Move the handle at the bottom carefully to the right and close the door, release the handle.
The door cannot be closed when the packages in the food compartment are too big.
Do not use force when closing the door!
Only use the product with the door is closed!
Cooling
Wait at least 5 minutes before switching to the cooling mode, if the product was ope-
rated in the heating mode before!
Depending on the input voltage used, move the „DC/AC" switch into the correct position:
AC = 220-240V~
DC = 12Vdc
The product is switched off, when the switch is in the „STOP" position.
Move the switch „WARM - STOP - COOL" to the position „COOL".
The green LED lights up (cooling), the fan at the back of the product starts.
Fill the food compartment with the desired foodstuffs/drinks; only use completely closed contai-
ners!
Close the door of the food compartment properly.
Our tip:
Place pre-cooled foodstuffs/drinks in the food compartment of the product. The mini-
mum temperature will be reached sooner.
The time taken for the cooling to reach the minimum temperature differs, depending on the quan-
tity and temperature of the foodstuffs/drinks and the ambient temperature.
The lowest temperature is reached after approximately 2 to 3 hours.
To switch off, move the switch „WARM - STOP - COOL" to the position „STOP". The green LED
goes out.
Move the switch „DC - STOP - AC" to the position „STOP".
Heating
Wait at least 5 minutes before switching to the heating mode, if the product was ope-
rated in cooling mode before!
Depending on the input voltage used, move the switch „DC - STOP - AC" into the correct position:
DC = 12Vdc
AC = 220-240V~/50Hz
The product is switched off, when the switch is in the „STOP" position.
Move the switch „WARM - STOP - COOL" to the position „WARM".
The red LED lights up (heating), the fan at the back of the product starts.
Fill the food compartment with the desired foodstuffs/drinks; only use completely closed contai-
ners!
Close the door of the food compartment properly.
Our tip:
Place pre-heated foodstuffs/drinks in the food compartment of the product. The
maximum temperature is reached sooner.
The time taken for the heating to reach the maximum temperature differs, depending on the
quantity and temperature of the foodstuffs/drinks and the ambient temperature.
The highest temperature is reached after approximately 2 hours.
To switch off, move the switch „WARM - STOP - COOL" to the position „STOP". The red LED
goes out.
Move the switch „DC - STOP - AC" to the position „STOP".
Maintenance and Cleaning
• The product does not require any maintenance, never take it apart. Servicing or repair may
only be carried out by a specialist.
• Switch off the product after use, and disconnect it from the operating voltage, remove the con-
nection cable, before cleaning.
• A clean, soft cloth is sufficient for cleaning the outside. Do not press on the surface too strongly,
since this may cause scratches.
Dust in the ventilation openings can be removed very easily with a long-haired, clean, soft
brush or with a vacuum cleaner.
• Clean the inside of the food compartment very carefully after each use to avoid the growth of
mould. Only use an suitable, clean, soft cloth for cleaning. The cloth can be moisten with warm
water; in addition, you can use a gentle detergent, which is suitable for cleaning dishes/cutlery.
Never put the product in or under water to clean it, this will destroy it!
Allow the food compartment to dry thoroughly before closing the food compartment's door and
storing the product.
• After long storage, the food compartment has to be cleaned again before use!
Disposal
Please dispose of the product, when it is no longer of use, according to the current
statutory requirements.
Technical Data
Operating voltage: ........................................12Vdc or 220-240V~/50Hz
Input: ............................................................Max. ca. 55W
Dimensions of the food compartment:..........Approx. 205 x 140 x 138mm (W x H x D)
Volume of the food compartment: ................Ca. 4L
Dimensions:..................................................Approx. 275 x 190 x 260mm (W x H x D)
Weight: ........................................................Approx. 2.1kg
Cooling temperature:....................................Down to +5°C
Heating temperature:....................................Up to +65°C
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2010 by Conrad Electronic SE.