Error Messages - Renkforce RF-PM-01 Bedienungsanleitung

d) Deleting or adjusting access data and setting menu
• Click the Manager (3) switch area or „Manager" on
the right in the task bar of the password manager
program menu to proceed to overview of all the
saved passwords.
• Proceed in the standard browser to the respective
website by clicking a square preceding relevant
entry. If several login data have been logged for a
website, you can choose the desired website login
by clicking the website entry in this list. A cross in
the square before an entry points out several login
data sets logged.
• Add a new entry by the (+) button or delete the
selected one by clicking (-). The eraser symbol
opens the input field of a website entry for changes. If you wish to alter an entry only to a
limited degree (e.g., retaining the password), do not change the respective entries or do not
make an entry. In case of several accounts available, choose the ones you wish to change
or to delete.
• Close the manager window by clicking the cross in the right upper corner.
Settings
Proceed from the management window by clicking the gear symbol to the next window to
exercise the following functions:
1 Close
Close the program window by clicking the cross in the right upper corner.
2 Automatic LOGIN
If you choose automatic logon of the password manager with master password, enable this
function and then enter your master password. Confirm by clicking OK.
You cannot enable the automatic logon and automatic logout functions at the same
time. With this function enabled, you choose to continuously store the master pass-
word on your computer and thus restrict the maximum achievable security.
3 Automatic LOGOUT
After the automatic logout (adjustable timeframe is 1 min to 8 h) is enabled, after expiration
of the set period, an information window will appear. The password manager logs out auto-
matically upon confirmation („OK") or expiry of the period. Pressing the „NO" button will
reset the count-down.
You cannot enable the automatic logon and automatic logout functions at the same
time. Depending on the hardware, disabling occurs in 1 -3 s. Logout from the sites
you are logged in does not occur automatically. New logon with the logged account-
ing data is disabled.
4 Changing master password
To change the master password of the password manager, press „Change PW", enter the
current master password, enter and then re-enter the new one. Confirm the change.
5 Creating BACKUP FILE
Save an encrypted file (x.POP) on your device. To do that, choose the „Backup" switch
area, introduce a secure encryption password and specify the location on your PC. Using
this file, you can transfer the content to a new password manager.
It is impossible to recover the password manager without the encryption password.
Do not use the same password as both master and encryption password.
6 Recovery of the password manager
Recover the backed up status of a password manager by clicking „Restore". Select the
desired backup (with .POP extension), enter the matching password and click „Restore".
This procedure will overwrite the current contents of the password manager.
7 Automatic hiding
8 Language settings
www.naver.com
naver
9 Version information
Update
Download the current update (at:) and launch it (double click). Observe the warning (see
above) and confirm by clicking OK. Enter the master password and create a backup, if any
important data must be saved in the password manager. Enter a backup password and choose
a location for the backup. After successful product identification and verification, a new operat-
ing system is written to the password manager. After successful update, confirm this by clicking
OK, remove the device and connect it again. After an update, the device additionally needs up
to a minute to initialise.

Error messages

Typical error messages as regards updates are:
• The software version of the program is more up to date than the version of the desired update
• No password manager detected on your device. Connect the device properly.
• Update could not be started. Restart your computer, reconnect the product correctly and
• The software version of the installed program not recognised. Restart your computer, recon-
• File write (FW) error: Communication error in the course of updates. Repeat the procedure.
Disposal
Technical data
Software version .................................. 1.7 (basis for this manual)
Operating voltage ................................ DC 5 V
Power consumption ............................. 0.5 W
Interface ............................................... high speed USB 2.0 (downward compatible)
Status indicator .................................... multicolour LED
Encryption algorithms .......................... AES256, SEED 256, ARIA hardware based security
Equipment group ................................. computer
Operating system ................................ Windows 7, Windows 8, Windows 10
Supported browsers ............................ Internet Explorer (IE), Chrome, Opera, QQ, 360safe,
Product dimensions ............................. 26 x 79 x 14 mm
Weight ................................................. 0.013 kg
Operating temperature ........................ 0 to 45 °C
Storage temperature ............................ -20 to 70 °C
This function minimises the menu window after login by clicking the menu button „Pass-
word Manager"
Toggle the menu language between D/GB/F/NL/I/PL using the menu item „Select Lan-
guage".
The language choice does not change the keyboard layout.
Displays the current version (firmware, software, and serial number) of your device.
Shut the password manager program on your computer before performing updates.
Never remove the hardware in the course of the updates. Before performing an
update, create a backup.
package.
make sure you have proper permissions for the updates.
nect the product correctly and make sure you have proper permissions for the updates.
Restart your computer, reconnect the product correctly and make sure you have proper per-
missions for the updates.
It is possible that mistakes in English language will be recognised by error messages.
Electronic devices are recyclable materials and do not belong in the household was-
te. At the end of its service life, dispose of the product according to the relevant
statutory regulations.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
© Copyright 2018 by Conrad Electronic SE.
chip
Sogou, Firefox
1593964_V2_0118_02_VTP_m_en