Intended Use; Explanation Of The Symbols; Safety Instructions - Renkforce 808579 Bedienungsanleitung

G Operating instructions
2.4 GHz digital receiver
Item No. 808579
Intended use
The product is used for the reception of radio AV signals via a radio camera suitable
for this purpose and for the conversion of an analogue AV signal, e.g. the signal that
can be shown on a monitor or recorded on a DVR.
The receiver's power is supplied by the wall plug transformer included in the delivery.
The safety instructions must be observed at all times!
Any use other than that described above could lead to damage to this product and
involves the risk of short circuits, fire, electric shock, etc. No part of the product may
be modified or converted!
This product complies with the applicable national and European requirements. All
names of companies and products are the trademarks of the respective owners. All
rights reserved.
Contents
• Receiver
• Antenna
• Wall plug transformer
• AV cable
• Operating instructions
Explanation of the symbols
The lightning symbol inside a triangle is a warning to inform you of potential
risks of personal injury, such as electrical shock.
This symbol indicates specific risks associated with handling, function and
use.
The "arrow" symbol indicates special tips and operating information.
Safety Instructions
The warranty will be void in the event of damage caused by failure to ob-
serve these safety instructions! We do not assume any liability for any re-
sulting damage!
We shall not accept liability for damage to property or personal injury
caused by incorrect handling or non-compliance with the safety instruc-
tions. In such cases, the warranty will be null and void.
a) General
• The unauthorized conversion and/or modification of the product is in-
admissible for reasons of safety and approval (CE). Never dismantle the
product.
• The product is not a toy and should be kept out of the reach of children.
Install and use the product where it is out of the reach of children.
• Do not carelessly leave the packaging material lying around, since it could
become a dangerous plaything for children.
• In business institutions, the accident prevention regulations of the Em-
ployer's Liability Insurance Association for Electrical Systems and Operat-
ing Facilities must be observed.
• The entire product is only intended for use in dry, enclosed spaces, it must
not get damp or wet.
• Do not expose the product to extreme temperatures, direct sunlight, in-
tense vibrations or heavy mechanical loading.
• Make sure that the connected cables are not pinched, kinked or damaged
by sharp edges.
• Handle the product with care; it can be damaged by impacts, blows or
falls even from a low height.
• If you notice any damage, don't use the product any more. Take it to a
specialist workshop.
Safe operation can no longer be assumed if:
- the product shows visible signs of damage
- the product ceases to function
- the product was stored for a longer period of time in unfavourable condi-
tions
- it was exposed to heavy loads during transport
• When the product is brought from a cold into a warm room (e.g. during
transport), condensation may form.
Allow the product to reach room temperature before you connect it to the
mains voltage. This may take several hours.
With moisture on the AC adapter there is also the danger to life from elec-
tric shock!
b) Wall plug transformer
• The design of the AC adapter complies with IEC Protection Class II (double
insulated electrical appliances).
• Connect the AC adapter only to a proper outlet of the public supply net-
work.
• The outlet for the wall plug transformer must be located in direct proximity
to the radio receiver and easily accessible.
• The AC adapter is only intended for use in dry, enclosed interiors; it must
not get damp or wet. There is a life-threatening hazard through an electric
shock!
• Do not pull the AC adapter from the power outlet by pulling on the cable.
• Protect the cable of the AC adapter from sharp edges and do not step on it.
• If the AC adapter is damaged, do not touch it; there is a danger to life from
electric shock!
Switch off the power supply to the outlet to which the AC adapter is con-
nected (e.g. switch off at the corresponding circuit breaker or remove the
safety fuse and then switch off the corresponding RCD).
Now disconnect the AC adapter from the outlet and take the product to a
specialized workshop.
• Only use the wall plug transformer provided to operate the radio receiver.
If the AC adapter is faulty, it must be replaced by an identical, stabilised
AC adapter with the same technical specifications (voltage/current).
Controls
7 6 5
1 Antenna
2 Video output (BNC)
3 Audio output (cinch)
4 Round low-voltage socket for the connection of the wall plug transformer provided
5 Western socket
6 LED
7 "PAIR" button (for registering a radio-controlled camera on the radio receiver
1
2 3 4