Denon DJ X1800 prime Benutzerhandbuch Seite 7

19. Channel Fader Start: Use this switch to enable or disable channel fader start. When
enabled, you can automatically start playback the SC5000 Prime units connected to each
channel by moving the channel fader upward.
20. Booth: Turn this knob to adjust the volume level of the booth outputs.
21. Master Level Meters: These LEDs display the audio signal level of the master mix (sent
out of the master outputs).
22. Master: Turn this knob to adjust the volume level of the master outputs.
23. Stereo/Mono Selector: Use this switch to set the channel configuration of the master
outputs: Stereo (binaural audio using separate left and right channels) or Mono (summed
monaural audio through both left and right channels).
24. Pan: Turn this knob to adjust the position of the master outputs' signal in the stereo field.
25. Mic 1 Input: Use a standard XLR or 1/4" (6.35 mm) cable (not included) to connect a
standard dynamic microphone to this input. Use the Mic 1 Level knob on the top panel to
control the volume level.
26. Mic 1/2 Level: Turn these knobs to adjust the volume levels of the corresponding
microphone inputs. The light next to each knob indicates the current signal level by its
color: green (normal/optimal) or red (maximum/peak).
27. Mic On/Off: Press these buttons to activate or deactivate the corresponding microphone.
28. Talk Over: Press this button to activate or deactivate the "talkover" feature, which
automatically reduces the volume level of the master mix when you speak into the
microphone. You can use the Utility menu to set how much the master mix volume level is
lowered and how quickly it returns to its normal level (see
29. Mic EQ (High, Low): Turn these knobs to boost or cut the high and low frequencies for
both microphones.
30. Headphone Outputs: Connect headphones to these 1/4" (6.35 mm) and 1/8" (3.5 mm)
jacks for monitoring the signal. Turn the Headphone Level knob to control the volume.
31. Headphone Level: Turn this knob to adjust the volume of the headphones.
32. Split Cue: When this switch is in the On position, the headphone audio will be "split" such
that all channels sent to cue channel are summed to mono and sent to the left headphone
channel and the master mix is summed to mono and sent to the right channel. When the
switch is in the Off position, the cue channel and master mix will be "blended" together.
33. Cue Mix: Turn this knob to adjust the balance between the cue output and the master mix
output in the headphones.
34. Displays: These displays show current information about the effects and tempo as well as
the Utility menu.
35. FX On/Off: Press this button to turn the BPM effects module on or off.
36. Wet/Dry: Turn this knob to adjust the balance between the "wet" signal (the BPM effect
module's output signal) and "dry" signal (audio without BPM effects applied).
37. Instant: Press this button to enable or disable Instant FX Mode for the FX touch strip.
38. FX Channel Assign: Turn this knob to select the channel to which the BPM effects
module will apply its effects: Channel 1, 2, 3, or 4; X-Fader A or B (either side of the
crossfader); Mic (both microphone signals); or Master (the master mix).
39. FX Select/Enter: Turn this knob to select an effect. While in the Utility menu, turn this
knob to select an option, and press it to confirm your choice or enter a submenu.
40. Back: Press this button to return to the previous screen in the Utility menu.
41. FX Cue: Press this button to preview the BPM effects in the headphones' cue channel.
Not all BPM effects can be previewed, though.
Operation > Utility Menu).
7