Working Advice - Bosch GTA 2600 Professional Originalbetriebsanleitung

OBJ_BUCH-843-004.book Page 13 Thursday, January 12, 2017 11:27 AM
No. Designation
Fastening kit
consisting of:
– Carriage bolt
10 M8 x 26
11 M6 x 46
12 M8 x 44
13 – Washer
14 – Lock washer
15 – Nut locking device
16 – Nut
17 – Assembly-sliding plate
18 – Assembly-sliding plate with slot
4 – Locking knob of the length stop
Additionally required tools (not in delivery scope):
– Cross-head screwdriver
– Adjustable spanner
Assembling the Saw Stand
Carefully remove all parts included in the delivery from their
packaging.
Remove all packaging material.
Setting Up the Saw Stand (see figures A1 – A2)
Lay the saw stand upside down on the floor (legs facing up-
ward).
Push the locking pin 19 in and tilt the leg upward until the
locking pin can be heard to engage.
Repeat this workstep with the other three legs.
Turn around the saw stand to the working position.
Ensure that the saw stand is stable and that all locking pins
have engaged.
The saw stand is easily aligned with the height-adjustable leg
9.
Loosen lock nut 20 and screw the leg in or out until the saw
stand is aligned level and all four legs face against the floor.
Mounting the Length Stop and Workpiece Support
(see figures B1–B2)
Screw the length stop 5 to the workpiece support 1 with car-
riage bolt 11 and locking knob 4.
Insert the workpiece support 1 into the table extension 2.
Tighten the locking knob 7 to lock the workpiece support.
Repeat the worksteps with the second workpiece support.
Preparing the Saw Stand
Preparing the Attachment Sets (see figure C)
for GCM 10 xx, GCM 12 xx, GTM 12
Insert one carriage bolt 12 each through assembly-sliding
plate 17 and 18.
Position assembly-sliding plate 17 with the carriage bolt in
the rear slot of the attachment set.
Position assembly-sliding plate 18 with the carriage bolt in
the front slot of the attachment set.
Repeat the worksteps with the second attachment set.
Bosch Power Tools
for GCM 8 S, GCM 8 SJ, GCM 800 S
Quantity
Insert one carriage bolt 12 through assembly-sliding plate 17
and one carriage bolt 10 through assembly-sliding plate 18.
Position assembly-sliding plate 17 with the carriage bolt in
the rear slot of the attachment set.
2
2
Position assembly-sliding plate 18 with the carriage bolt in
4
the front slot of the attachment set and secure the carriage
4
bolt with the nut locking device 15 against falling out.
4
Repeat the worksteps with the second attachment set.
2
Fastening the Power Tool to the Attachment Sets
4
(see figure D)
2
Position the power tool in the transport position. Notes on the
2
transport position are given in the operating instructions of
2
the respective power tool.
Raise one side of the power tool and position the carriage
bolts of the attachment set at the correct distance to the
mounting holes of the power tool.
Note: Power tools with off-set mounting holes can also be fas-
tened with help of the slot in the assembly-sliding plate 18
and the lateral slot in the attachment set 6.
Lower the power tool onto the carriage bolts and loosely
screw the attachment set and the power tool together with
the washers 13, lock washers 14 and nuts 16.
Screw the locking knob 8 into the corresponding hole of the
attachment set 6.
Repeat the worksteps with the second attachment set.
Fastening the Attachment Sets with the Power Tool
onto the Saw Stand (see figures E1 – E2)
Align both attachment sets parallel to each other.
Position the power tool centred on the saw stand in the se-
quence shown. Firstly, allow the rounded-off part of the at-
tachment sets to rest against the front rail (1), then slowly and
carefully lower the power tool (2) until it is seated securely on
the rear rail.
If required, move the power tool on the attachment sets 6 so
that the weight is positioned centrally on the saw stand.
Now, firmly tighten the nuts 16 for final fastening of the power
tool.
Afterwards, firmly tighten both locking knobs 8 of the attach-
ment sets.
Operation

Working Advice

Do not overload the saw stand. Always observe the maximum
carrying capacity of the saw stand and the two table exten-
sions.
Always hold the workpiece firmly, especially the longer and
more heavy section. After cutting through the workpiece, the
centre of gravity may become dislocated in such an unfavour-
able manner that the saw stand tips over.
English | 13
1 609 92A 2MA | (12.1.17)