LD Systems CURV 500 SmartLink Bedienungsanleitung

USER´S MANUAL
LDCURV500SLA(W)T
SAFETY INFORMATION
1. Please read these instructions carefully.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.
5. Use the equipment only in the intended manner and for the intended purpose.
6. During installation, observe the applicable safety regulations for your country.
7. Never place sources of ignition, e.g., burning candles, on the equipment.
8. Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment - in
this case, observe the special instructions noted below. Do not expose this equipment to flammable materials,
fluids or gases.
9. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers filled with
liquids, such as vases or drinking vessels, on the equipment.
10. Make certain that objects cannot fall into the device.
11. Use this equipment only with the accessories recommended and intended by the manufacturer.
12. Do not open or modify this equipment.
13. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to tripping
hazards.
14. During transport, make certain that the equipment cannot fall down and possibly cause property damage
and personal injuries.
15. If your equipment is no longer functioning properly, if fluids or objects have gotten inside the equipment or if
it has been damaged in another way, switch it off immediately and unplug it from the mains outlet (if it is a
powered device). This equipment may only be repaired by authorized, qualified personnel.
16. Clean the equipment using a dry cloth.
17. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate
plastic and paper/cardboard.
18. Plastic bags must be kept out of reach of children.
CAUTION – HIGH VOLUME LEVELS WITH AUDIO PRODUCTS!
This equipment is intended for professional use. Therefore, commercial use of this equipment is subject to the
respectively applicable national accident prevention rules and regulations. As a manufacturer, Adam Hall is ob-
ligated to notify you formally about the existence of potential health risks. Hearing damage due to high volume
and prolonged exposure: When in use, this product is capable of producing high sound-pressure levels (SPL) that
can lead to irreversible hearing damage in performers, employees, and audience members. For this reason, avoid
prolonged exposure to volumes in excess of 90 dB.
To prevent possible hearing damage, avoid listening at high volume levels over long periods of time.
Even exposure to short bursts of loud noise can result in hearing loss. Please keep the volume
constantly at a comfortable level.
MANUFACTURER'S WARRANTY & LIMITATION OF LIABILITY
You can find our current warranty conditions and limitation of liability at: https://cdn-shop.adamhall.com/media/
pdf/Manufacturers-Declarations-LDSYSTEMS_DE_EN_ES_FR.pdf
To request warranty service for a product, please contact Adam Hall GmbH, Adam-Hall-Str. 1, 61267 Neu Anspach
/ Email Info@adamhall.com / 49 (0) 6081 / 9419-0
PROPER DISPOSAL OF THIS PRODUCT
(WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT)
(Valid in the European Union and other European countries with waste separation)
This symbol on the product, or the documents accompanying the product, indicates that this appliance may not be
treated as household waste. This is to avoid environmental damage or personal injury due to uncontrolled waste disposal.
Please dispose of this product separately from other waste and have it recycled to promote sustainable economic activity.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details on where and how they can recycle this item in an environmentally friendly manner.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This
product should not be mixed with other commercial wastes for disposal
CE CONFORMITY
Adam Hall GmbH hereby confirm that this product meets the following guidelines (where applicable):
R&TTE (1999/5/EC) or RED (2014/53/EU) from June 2017 / Low-voltage directive (2014/35/EU)
EMC Directive (2014/30/EU) / RoHS (2011/65/EU) / The full declaration of conformity can be found at www.adam-
hall.com. You can also request it via info@adamhall.com
LDCURV500SLA(W)T - CURV 500® SMARTLINK® ADAPTER 100 V/70 V
SmartLink® adapter as the base for up to 4 CURV 500® array satellites for 100 V/70 V installations.
8
6
8
6
7
7
Adam Hall GmbH · Adam-Hall-Str. 1 · 61267 Neu-Anspach · Germany
Tel.: (+49) 60 81 / 94 19 0 · Fax: (+49) 60 81 / 94 19 1000 · eMail: mail@adamhall.com
CONNECTIONS, CONTROLS AND MOUNTING
1
INPUT SELECT: switch with 2 positions to adjust the SmartLink adapter to 100 V or 70 V installation amplifiers.
Before connecting, place the switch in the position corresponding to installation amplifiers.
2
OUTPUT POWER: switch with 4 positions for setting the output power. The maximum output power is 80 W at
4 ohms (switch in 100% position). Since a CURV 500 satellite has an impedance of 16 ohms, setting the
output power to adjust the volume is independent of the number of connected satellites (maximum 4 units).
Using a suitable tool (flat head screwdriver), place the switch in the position corresponding to the desired
output power (12.5%, 25%, 50%, 100%).
3
SIGNAL INPUT: screw/plug connection to connect an installation amplifier (screw/plug connection included).
When connecting the cables, make sure to have the correct polarity.
4
Four rubber feet provide stability for desktop applications. For the installation of the ceiling mount bracket
LDCURV500CMB(W), unscrew the rubber feet (M3 thread).
5
Two M6 threads for attaching the wall mounting bracket LDCURV500WMB(W), or the truss mounting bracket
LDCURV500TMB.
6
Grooves to mount the LD CURV 500 satellites.
7
The contacts ensure the electrical connection to the CURV 500 satellites.
8
The locking mechanism provides for a reliable mechanical connection with the CURV 500 satellites.
Slide a CURV 500 satellite from the rear onto the SmartLink adapter until it stops, while pressing the spring-loaded
release button on the side of the satellite. Ensure that the two guide rails of the satellite properly slide into the grooves
of the SmartLink adapter in order to ensure a tight fit and establish a contact for both components. Now release the
button to lock the connection and to bring the button back to its original position. Proceed in the same manner as
described above to add other satellites. When disassembling, please proceed in reverse order.
SPECIFICATIONS
Model type:
Product type:
Connectors:
Frequency Response
(100V/70V):
THD+ N:
Controls:
Output power / switch position
(100V/70V):
Material:
Surface:
Colour:
Dimensions (W x H x D):
Weight:
Features:
Included Accessories:
4
4
3
5
5
LDCURV500SLA(W)T
70V/100V SmartLink ® adapter as base for up to 4 CURV 500 ® array
satellites.
screw-/plug-in terminal 2 pole
20Hz - 20kHz
0.02%
70V/100V switch, 12.5% / 25% / 50% / 100% switch
1 satellite (16 ohms): 12.5% = 2W, 25% = 5W, 50% = 10W, 100% = 20W
2 satellites (8 ohms): 12.5% = 5W, 25% = 10W, 50% = 20W, 100% = 40W
3 satellites (5.3 ohms): 12.5% = 8W, 25% = 15W, 50% = 30W, 100% = 60W
4 satellites (4 ohms): 12.5% = 10W, 25% = 20W, 50% = 40W, 100% = 80W
Diecast Aluminium
Powder coating
black (LDCURV500SLAT)
white (LDCURV500SLAWT)
122 x 57 x 122 mm
1.15 kg
2x M6 thread for optional wall/truss mount, M6 thread for safety eye
bolt, SmartLink® System, 4x rubber feet for desktop use
screw-/plug-in connector 2 pole black
4
1
2
4
EN