Prior To Operation; Installing And Rem Oving Bits - Hitachi M 12V2 Bedienungsanleitung

PRIOR TO OPERATION

1. Pow er source
Ensure that the pow er source to be utilized conform s
to the pow er requirem ents specified on the product
nam eplate.
2. Pow er sw itch
Ensure that the pow er sw itch is in the OFF position.
If the plug is connected to a receptacle w hile the
pow er sw itch is in the ON position, the pow er tool
w ill start operating im m ediately, w hich could cause
a serious accident.
3. Extension cord
When the w ork area is rem oved from the pow er
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.

INSTALLING AND REM OVING BITS

WARNING
Be sure to sw itch pow er OFF and disconnect the
plug from the receptacle to avoid serious trouble.
1. Installing bits
(1) Clean and insert shank of bit into the collet chuck
until shank bottom s, then back it out approxim ately
2 m m .
(2) With the bit inserted and pressing the lock pin
holding the arm ature shaft, use the 23 m m w rench
to firm ly tighten the collet chunk in a clockw ise
direction (view ed from under the router). (Fig. 1)
CAUTION
Ensure that the collet chuck is firm ly tightened after
inserting a bit. Failure to do so w ill result in dam age
to the collet chuck.
Ensure that the lock pin is not inserted into the
arm ature shaft after tightening the collet chuck.
Failure to do so w ill result in dam age to the collet
chuck, lock pin and arm ature shaft.
(3) When using the 8 m m diam eter shank bit, replace
the equipped collet chuck w ith the one for 8m m
diam eter shank bit w hich is provided as the standard
accessory.
2. Removing Bits
When rem oving the bits, do so by follow ing the
steps for installing bits in reverse order.
CAUTION
Ensure that the lock pin is not inserted into the
arm ature shaft after tightening the collet chuck.
Failure to do so w ill result in dam age to the collet
chuck, lock pin and arm ature shaft.
HOW TO USE THE ROUTER
1. Adjusting depth of cut (Fig. 2)
(1) Place the tool on a flat w ood surface.
(2) Tu r n t h e q u i ck
counterclockw ise direction until the quick adjustm ent
lever stops. (Fig. 3)
(3) Turn the stopper block so that section to w hich the
cutting depth setting screw on a stopper block is
not attached com es to the bottom of the stopper
pole. Loosen pole lock knob allow ing the stopper
pole to contact w ith stopper block.
ad j u st m en t l ev er i n
(4) Loosen the lock lever and press the tool body until
the bit just touches the flat surface. Tighten the lock
lever at this point. (Fig. 4)
(5) Tighten pole lock knob. Align the depth indicator
w ith the " 0" graduation of scale.
(6) Loosen pole lock knob, and raise until indicator
aligns w ith the graduation representing the desired
cutting depth. Tighten pole lock knob.
(7) Loosen the lock lever and press the tool body dow n
until the stopper block to obtain the desired cutting
depth.
Your router allow s you to finely adjust depth of cut.
(1) Attach knob to fine adjustm ent knob.
(2) Turn the quick adjustm ent lever in a clockw ise
direction until the quick adjustm ent lever stops w ith
the stopper screw . (Fig. 5)
If the quick adjustm ent lever does not stop w ith the
stopper screw , the bolt screw is not properly fitted.
If this occurs, slightly loosen the lock lever and
press dow n on the unit (router) hard from the top
and turn the quick adjustm ent lever again after
properly fitting the bolt screw .
(3) The depth of cut can be adjusted w hen the lock
lever is loosened, by turning the fine adjustm ent
kn o b . Tu r n i n g
counterclockw ise results in shallow er cut, w hereas
turning it clockw ise results in a deeper cut.
CAUTION
Ensure that the lock lever is tightened after finely
adjusting depth of cut. Failure to do so w ill result
in dam age to the quick adjustm ent lever.
2. Stopper block (Fig. 6)
The 2 cut-depth setting screw s attached to the
stopper block can be adjusted to sim ultaneously set
3 different cutting depth. Use a w rench to tighten
the nuts so that the cut-depth setting screw s do not
com e loose at this tim e.
3. Guiding the router
WARNING
Be sure to sw itch pow er OFF and disconnect the
plug from the receptacle to avoid serious trouble.
(1) Tem plate guide adapter
1 Loosen the 2 tem plate guide adapter screw s, so that
the tem plate guide adapter can be m oved. (Fig. 8)
2 Insert the centering gauge through the hole in the
tem plate guide adapter and into the collet chuck.
(Fig. 9)
3 Tighten the collet chuck by hand.
4 Tighten the tem plate guide adapter screw s, and pull
out the centering gauge.
(2) Tem plate guide
Use the tem plate guide w hen em ploying a tem plate
for producing a large quantity of identically shaped
products. (Fig. 10)
As show n in Fig. 11, to install insert tem plate guide
in center hole in tem plate guide adapter w ith 2
accessory screw s.
a
A tem plate is a profiling m old m ade of plyw ood
or thin lum ber. When m aking a tem plate, pay
particular attention to the m atters described below
and illustrated in Fig. 12.
When using the router along the interior plane of
the tem plate, the dim ensions of the finished product
w ill be less than the dim ensions of the tem plate
by an am ount equal to dim ension " A" , the difference
English
t h e f i n e ad j u st m en t kn o b
8