Declaration of Conformity Westermo Teleindustri AB Declaration of conformity The manufacturer Westermo Teleindustri AB SE-640 40 Stora Sundby, Sweden Herewith declares that the product(s) Type of product Model Art no Table top converter RS232-RS422/485 MA-45 AC 3045-0001 is in conformity with the following EC directive(s).
Seite 3
Specifikationer MA-45 Överföring Asynkront, full/halv duplex eller simplex Gränssnitt 1 EIA RS-232-C/ITU-T V.24 25-polig D-sub hylsdon, DCE Gränssnitt 2 EIA RS-422/RS-485/ ITU-T V.11 Överföringshastighet Upp till 115,2 kbit/s Lysdioder Power, RD, CTS, RTS, TD Isolation Fullständig galvanisk isolation med optokopplare (data) resp. transformator (matning) Isolationsspänning 1 500 V Överspänningsskydd Nät: Genombrottsspänning 440 V vid 230 V AC och 220 V vid 115 V AC Gränssnitt 2: Genombrottsspänning sändare och mottagare 7 V Avledningsförmåga 0,6 kW under 1ms Strömförsörjning Omkopplingsbart mellan 115/230 V +15/–10% 48–62 Hz Säkring AC: 100 mA snabb 5x20 mm DC: 1,6 A snabb 5 x 20 mm Effektförbrukning AC: Max 22 mA vid 230 V, max 44 mA vid 115 V DC: Max 1,4 W Temperaturområde 5–50°C, omgivningstemperatur Fuktighetsområde 0–95% RH, utan kondensation Mått 161x139x53 mm BxDxH Vikt AC: 0,5 kg DC: 0,25 kg Montering ...
Seite 4
Inställningar MA-45 kan genom inställningar anpassas till ett flertal olika driftförhållanden. Samtliga omkopplare i MA-45 är åtkomliga när lådans lock avlägsnas. Detta sker lätt med hjälp av t.ex en skruvmejsel. VARNING! ÖPPNA EJ ANSLUTEN ENHET LINE V.24/RS-232-C CONNECTION CONNECTION 1 2 3 4 5 Val av hastighet Hastighet Vändtid ON 1 200 bit/s 780 µs 1 2 3 4 5 6 7 8 1 - 4 1 - 8 ON 2 400 bit/s 410 µs 1 2 3 4 5 6 7 8 ON ...
Seite 5
2/4-tråds överföring Terminering med fail-safe ON 2-tråd ON 1 2 3 4 5 6 7 8 Terminerad (4-tråd) 1 2 3 4 ON 4-tråd ON 1 2 3 4 5 6 7 8 Terminerad (2-tråd) 1 2 3 4 ON Ingen terminering Data eller RTS-styrning 1 2 3 4 ON Fail-safe funktionen gör att mottagaren alltid uppfattar ...
Seite 6
Anslutningar Linjeanslutning (5-polig skruvplint) Riktning Anslutning ITU-T V.11 nr. Benämning Mottagare 1 A’ (R+) Mottagare 2 B’ (R–) Sändare 3 A (T+) Sändare 4 B (T–) 5 Skärm Definitionen R+/R–, T+/T– kan variera mellan olika tillverkare. Terminalanslutning (DCE) (RS-232-C/V.24, 25-Polig D-sub, hylsdon) Riktning Anslutning ITU-T V.24 Signalnamn Benämning I 2 103 ...
Seite 7
Linjekoppling 1) Om skärmad kabel används, anslut skärmen endast i en ände för att undvika jordströmmar. Överföringsavstånd (gränssnitt 2) Använd partvinnad kabel. Max ledningslängd 1 200 m (gäller för kabel med area 0,3 mm² och kapacitans 42 pF/m) Överföringsegenskaperna förbättras med sänkt kapacitans och ökad kabelarea. I störningsrik miljö bör skärmad kabel användas. MA-45 DC Specifikationer Inspänningsområde 12–36 V DC Effektförbrukning Max 2 W Isolationsspänning 1 000 V Säkring F1 1,6 A snabb 5x20 mm I övrigt gäller MA-45 AC specifikationerna Inställningar Enligt MA-45 AC Anslutning Enligt MA-45 AC, förutom matning Ansl. Benämning 1 + Spänning 2 – Spänning 3 6045-2002...
Seite 8
Tips MA-45 arbetar med linjegränssnittet RS-422/485. RS-422/485 är gränssnitt konstruerade för multidroppapplikationer. Då man kopplar upp en RS-422 alt. RS-485 förbindelse skall man tänka på att installera ett bussnät, d.v.s det får inte vara förgreningar på kablaget. För att få rätt kabelavslutning skall masteromvandlaren samt den sist anslutna enhetens mottagare termineras. Nedan visas multidroppinstallation med terminering i RS-485 (2-tråds) och RS-422 (4-tråds) kommunikation. Linjesändaren på MA-45 är endast aktiv då data mottages på RS-232 sidan. Om det uppkommer något problem vid inkoppling av MA-45 kan lysdiodsindikeringarna vara till värdefull hjälp vid felsökning. • PWR: Indikerar att enheten är spänningssatt. • RD: Indikerar mottagen data på linjesidan • CTS: Indikerar samma som RTS. • RTS: Indikerar RTS signalen från inkopplad utrustning. • TD: Indikerar mottagen data på RS-232 sidan. OBS! R +/R–, T+/T– definitationerna är ej standardiserade, det kan hjälpa att skifta A och B om enheten inte fungerar. 6045-2002...
Seite 9
Specifications MA-45 Transmission Asynchronous, full/half duplex or simplex Interface 1 EIA RS-232-C/ITU-T V.24 25-position D-sub female, DCE Interface 2 EIA RS-422/RS-485/ITU-T V.11 Data rate Up to 115.2 kbit/s Indicators Power, RD, CTS, RTS, TD Insulation Galvanic insulation with opto-coupler (data transmission) and transformer (supply) Insulation voltage 1 500 V Overvoltage protection Mains: Breakdown voltage 440 V at 230 V AC and 220 V at 115 V AC Interface 2: Breakdown voltage transmitter and receiver 7 V. Surge capacity 0.6 kW for 1ms Power supply Switchable 115/230 V +15/–10% 48–62 Hz Fuse AC: 100 mA fast 5x20 mm DC: 1.6 A fast 5 x 20 mm Power consumption AC: Max 22 mA at 230 V, max 44 mA at 115 V DC: Max 1.4 W Temperature range 5–50°C, ambient temperature Humidity 0–95% RH, non-condensing Dimensions 161x139x53 mm WxDxH Weight AC: 0.5 kg DC: 0.25 kg Mounting Table top 6045-2002...
Switch settings The MA-45 can through different switch settings be adapted to a variety of running conditions. To set the switches, open the plastic case with e.g. a screw-driver. DANGER! DO NOT OPEN CONNECTED UNIT LINE V.24/RS-232-C CONNECTION CONNECTION 1 2 3 4 5 Selection of data rate Data Turning Rate time ON 1 200 bit/s 780 µs 1 2 3 4 5 6 7 8 1 - 4 1 - 8 ON 2 400 bit/s 410 µs ...
2/4-wire transmission Terminering with fail-safe ON 2-wire ON 1 2 3 4 5 6 7 8 Terminated (4-wire) 1 2 3 4 ON 4-wire ON 1 2 3 4 5 6 7 8 Terminated (2-wire) 1 2 3 4 ON No termination Data control by data 1 2 3 4 flow or RTS-control The fail-safe function forces the signal state of the ...
Seite 12
Connections Line connection (5-Position screw-terminal) Direction Connection ITU-T V.11 no. Description Receiver 1 A’ (R+) Receiver 2 B’ (R-) Transmitter 3 A (T+) Transmitter 4 B (T-) 5 Shield The definations R+/R–, T+/T– can be various between different manufactures. Terminal connection (DCE) (RS-232-C/V.24, 25-Position D-sub, female) Direction Connection ITU-T V.24 Signal name Code I 2 103 ...
Line connection 1) If shielded cable is used, connect the shield only at one end to avoid ground currents. Transmission range (interface 2) Use twisted pair cable. Max transmission range 1 200 metre. (cable specifications 0.3 mm² and capacitance 42 pF/m). The transmission range will increase if a cable with lower capacitance and larger diameter is used. Use shielded cable in heavy industrial environments. MA-45 DC Specifications Power supply 12–36 V DC Power consumption Max 2 W Insulation 1 000 V Fuse F1 1.6 A fast 5x20 mm All other specifications according to MA-45 AC Switch settings According to MA-45 AC Connections According to MA-45 AC, except power supply Connection Power supply 1 + Voltage 2 – Voltage 6045-2002...
Seite 14
Hints The MA-45 uses the RS-422/485 interface. RS-422/485 was designed for multidrop appli- cations. When a system is installed it should form a bus structure (see diagrams). Star shaped networks should never be created, there are other Westermo products designed to work in star net applications. To install correctly, an RS-422/485 network should be terminated at the correct points. The recommendation is to terminate the receiver on the master unit and the final bus slave unit. See diagrams for details of how this is done with RS-485 (2 wire) and RS-422 (4 wire). The line transmitter used in the MA-45 is activated by data received on the RS-232 interface, unlike conventional converters that rely on a control signal (e.g. RTS). If any problems do occur on set up of the MA-45, the LED’s will be helpful. • PWR: The unit has power. • RD: Data received on the RS-422/485 interface. • CTS: Follows RTS • RTS: Status of RTS from the RS-232 interface • TD: Data received on RS-232 interface N.B. R +/R–, T+/T– definitations are not standard, it can help to shift A and B if the unit does not work. 6045-2002...
Technische Daten MA-45 Übertragungsarten Asynchron, Voll-/Halbduplex oder Simplex Schnittstelle 1 EIA RS-232-C/ITU-T V.24 25 polige Sub-D-Buchse, Schraubklemme Schnittstelle 2 EIA RS-422/RS-485/ITU-T V.11 Übertragungsraten Bis zu 38,4 kbit/s Leuchtdioden Betrieb, RD, CTS, RTS, TD Isolation Galvanisch Isoliert mittels Optokoppler (Datenübertragung) und Transformator (Spannungsversorgung) Isolationsspannung 1 500 V Überspannungsschutz Netz: Durchbruchspannung 440 V bei 230 V und 220 V bei 115 V AC Schnittstelle 2: Durchbruchspannung Sender und Empfänger 7 V. Stromstoßkapazität 0,6 kW / 1 ms Spannungsversorgung 115/230 V +15/–10% 48–62 Hz Sicherung AC: 100 mA flink 5x20 mm DC: 1,6 A flink 5 x 20 mm Leistungsaufnahme AC: Max 22 mA bei 230 V, max 44 mA bei 115 V DC: Max 1,4 W Umgebungstemperatur 5–50°C Luftfeuchtigkeit 0–95%, nicht kondensierend Abmessungen 161x139x53 mm Gewicht AC: 0,5 kg DC: 0,25 kg Installation ...
DIP-Schalter Einstellung Das MA-45 bietet verschiedene Einstellmöglichkeiten zur Abstimmung auf verschiedenste Betriebsverhälnisse. Um die DIP-Schalter einzustellen muß die Gehäuseabdeckung z.B. mit Hilfe eines Schraubendrehers abgenommen werden. Achtung! Angeschlossene Geräte nicht öffnen LINE V.24/RS-232-C CONNECTION CONNECTION 1 2 3 4 5 Übertragungsrate Über- Umschalt- tragungs- zeit rate ON 1 200 bit/s 780 µs 1 - 4 1 - 8 1 2 3 4 5 6 7 8 ON 2 400 bit/s 410 µs ...
2/4 Draht Übertragung Termination mit fail-safe ON 2-Draht ON 1 2 3 4 5 6 7 8 4-Draht Termination 1 2 3 4 ON 4-Draht ON 1 2 3 4 5 6 7 8 2-Draht Termination 1 2 3 4 ON keine Termination Datensteuerung mittels 1 2 3 4 Datenfluß oder RTS-Steuerung Die fail-safe Funktion zwingt den Empfänger in AUS- ON ...
Seite 18
Leitungsanschluß (5-polige Schraubklemme) Richtung Nr. ITU-T V.11 Beschreibung Empfänger 1 A’ (R+) Empfänger 2 B’ (R–) Sender 3 A (T+) Sender 4 B (T–) 5 Schirmung Die Bezeichnungen R+/R–, T+/T– können abhängig vom Hersteller variieren. Terminal connection (DCE) (RS-232-C/V.24, 25-Position D-sub, female) Richtung Pin Nr. ITU-T V.24 Beschreibung Bezeichnung I ...
Leitungsanschluß 4-Draht 2-Draht RS-422 RS-485 MA-45 MA-45 Gerät Gerät Twisted Pairs A’ Sender Empfänger B’ Twisted Pairs Sender/ Sender/ Sender A’ A/A’ Empfänger A/A’ Empfänger Empfänger B’ B/B’ B/B’ Schirm Schirm 1) B ei Verwendung von abgeschirmten Kabeln den Schirm nur auf einer Seite anschließen um Erdströme zu vermeiden Übertragungsweiten: Benutzen Sie paarverseilte Leitungen. Maximale Übertragungsweite 1 200 m. (bei Kabelspezifikationen von 0,3 mm² und 42 pF/m). Die Übertragungsweite nimmt bei kleinerer Kapazität und größerem Durchmesser zu. Benutzen Sie abgeschirmte Kabel in schlechter Umgebung. MA-45 DC Technische Daten ...
Seite 20
Tips Das MA-45 besitzt eine RS-422/485 Schnittstelle. Der Schnittstellenstandard RS-422/485 wurde für Mehrpunktverbindungen entwickelt. Dieser Standard ist für Busnetze (siehe Beispiele) geeignet. Sternnetze sollten vermieden werden. Für eine korrekte Installation eines RS-422/485 sollte an den richtigen Punkten die Termination eingeschaltet werden. Es sollte am Empfänger des Masters und letzten Slave die Termination gesetzt sein. Siehe Beispiele für RS-485 (2-Draht) und RS-422 (4-Draht) Termination. Der Leitungssender des MA-45 wird aktiviert sobald Daten an der RS-232 Schnittstelle empfangen werden, nicht wie normale Konverter die ein Kontrollsignal z.B. RTS benötigen. Bei Problemen mit der Einstellung des MD-42 können die LED´s hilfreich sein • PWR Das Gerät hat Versorgungsspannung • RD Daten Empfang an der RS-422/485 Schnittstelle • CTS folgt RTS. • RTS zeigt den Status der RS-232 Schnittstelle an. • TD Daten Empfang an der RS-232 Schnittstelle Hinweis: D ie Bezeichnungen R+/R-, T+/T– sind nicht Standard, es kann bei Problemen helfen, A und B zu tauschen. 6045-2002...
Seite 21
Spécifications MA-45 Transmission Asynchrone, full/half duplex ou simplex Interface 1 EIA RS-232-C/ITU-T V.24 Connecteur sub-D 25 points femelle, DCE Interface 2 E IA RS-422/RS-485/ITU-T V.11 Bornier à vis 5 points Vitesse Jusqu'à 115,2 Kbit/sec Indicateurs LED Power, RD, CTS, RTS, TD Isolation Isolation galvanique avec opto-coupleur (transmission de données) et transformateur (alimentation) Tension d’isolement 1 500 Volts Protection surtension Secteur : Tension de claquage 440 V à 230 V AC et 220 V à 115 V AC Interface 2 : Tension de claquage émetteur/récepteur 7 V. Surcharge instantanée 0,6 kW pour 1 ms Alimentation Configurable 115 V/230 V AC +15/–10% 48–62 Hz Fusible AC 100 mA rapide 5x20 mm DC 1,6 A rapide 5x20 mm Consommation AC : Max 22 mA à 230 V AC, max 44 mA à 115 V DC : Max 1,4 W Gamme température 5–50°C température ambiante Humidité 0–95% RH non condensé Dimensions 161x139x53 mm (LxHxP) Poids AC: 0,5 kg ...
Seite 22
Configuration des micro-interrupteurs Le MA-45 s’adapté à différentes conditions d’utilisation à l’aide de la configuration des micro-interrupteurs. Pour accéder à ces micro-interrupteurs, ouvrir le coffret à l’aide d’un tournevis placé à l’arrière entre le couvercle et le fond du boîtier. L’ouverture se fait par rotation du tournevis. ATTENTION ! Ne pas ouvrir sous tension LINE V.24/RS-232-C CONNECTION CONNECTION 1 2 3 4 5 Configuration du débit des données Temps de Débit Retourne- des données ment 1 - 4 1 - 8 ON 1 200 bit/s 780 µs 1 2 3 4 5 6 7 8 ON ...
Seite 23
Transmission 2/4 Fils Terminaison avec niveau de sécurité ON 2 fils ON 1 2 3 4 5 6 7 8 Terminé (4 fils) 1 2 3 4 ON 4 fils ON 1 2 3 4 5 6 7 8 Terminé (2 fils) 1 2 3 4 ON Pas de terminaison Contrôle retournement 1 2 3 4 ON La fonction niveau de sécurité force l’état du signal Flux de données ...
Seite 24
Connexions Connexion Ligne (Bornier à vis 5 points) Direction N° ITU-T V.11 Description Récepteur 1 A’ (R+) Récepteur 2 B’ (R–) Emetteur 3 A (T+) Emetteur 4 B (T–) 5 Blindage Les définitions R+/R–, T+/T– peuvent changer suivant les constructeurs. Connexion Terminal (DCE) (RS-232-C/V.24/V.28, Connecteur sub-D 25 points femelle.) Direction point ITU-T V.24 Description N° I 2 103 TD/Donnée transmise O ...
Connexion Ligne 4 fils 2 fils Equipement Equipement MA-45 MA-45 RS-422 RS-485 Paires Torsadées A’ Emetteur Récepteur B’ Paires Torsadées Emetteur/ Emetteur/ Emetteur A’ A/A’ Récepteur A/A’ Récepteur Récepteur B’ B/B’ B/B’ Blindage Blindage 1) S i on utilise un câble blindé, connecter le blindage uniquement à une extrémité afin d’éviter les retours de courant de terre. Distance de transmission (interface 2) La distance de transmission maximale est de 1 200 m avec un câble en paire torsadée. (Spécifications câble 0.3 mm² et capacité de 42 pF/m). La distance de transmission augmentera si on utilise un câble ayant une section plus ...
Conseils Pratiques Le MA-45 utilise une interface RS-422/485. Le standard RS422/485 a été conçu pour des applications multipoints. Le réseau est installé sous la forme d’une structure bus (voir diagramme). Les réseaux en forme d’étoile sont proscrits. Il existe d’autres produits Westermo qui permettent de travailler avec un réseau en étoile. Une installation correcte d’un réseau RS-422/485 doit toujours être équipée d’une termi- naison sur les points correspondants. Il est indispensable d’équiper de terminaisons le récepteur de l’unité maître ainsi que le dernier esclave qui termine le bus. Le diagramme ci-contre vous montre comment est réalisée une connexion RS-485 (2fils) et RS-422 (4 fils) La fonction émission utilisée dans le MA-45 peut être activée soit par détection du flux de données reçu sur le port RS-232, soit par le contrôle RTS en modifiant le micro-inter- rupteur correspondant ( voir page 3 contrôle retournement). Si un problème survient pendant la configuration du MA-45, les LED de statut peuvent vous aider. • PWR: L’unité est alimentée. • RD: Réception de données sur l’interface RS-422/485. • CTS: Suit le signal RTS. • RTS: Statut du signal RTS provenant de l’interface RS-232. • TD: Réception de données sur l’interface RS-232/V.24. Max 1200 mètres 0,3 mètre Max Terminaison 32 connexions Max 0,3 mètre Max...
Block diagram V.11/RS-422 V.24/RS-232 RS-485 TD LED TD LED RTS LED S3:4 S3:3 Bus termination Bus termination S3:2 S3:1 S2:6 A’ B’ Shield 230/ Power Insulated power supply 115V supply Switch...
Seite 28
Westermo • SE-640 40 Stora Sundby, Sweden Tel +46 16 42 80 00 Fax +46 16 42 80 01 E-mail: info@westermo.com www.westermo.com Sales Units Sweden Singapore Westermo Data Communications Westermo Data Communications Svalgången 1, Vallbyinstitutet, 724 81 Västerås 2 Soon Wing Road #08-05, Tel: +46 (0) 21 548 08 00 • Fax: (0) 21 35 18 50 Soon Wing Industrial Building info.sverige@westermo.se • www.westermo.se Singapore 347893 Tel: +65 6743 9801 • Fax: +65 6745 0670 United Kingdom sales@westermo.com.sg • www.westermo.com.sg Westermo Data Communications North America Talisman Business Centre Duncan Road, Park Gate, Southampton. SO31 7GA Westermo Data Communications Tel: +44 (0) 1489 580 585 • Fax: +44 (0) 1489 580 586 939 N. Plum Grove Road, Suite F, sales@westermo.co.uk • www.westermo.co.uk IL 60173 Schaumburg, USA Tel: +1 847 619 6068 • Fax: +1 847 619 66 74 Germany info@westermo.com • www.westermo.com Westermo Data Communications Taiwan Goethe Strasse 67 ...