Troubleshooting Guide
Often, what appears to be a malfunction is due to user error.
Before calling for service, please consult the following table.
Problem
• The fuse is blown.
• The power supply pin (yellow) of the 10-pin connection cord
Power cannot be turned on
(the POWER indicator
• The power control pin (blue) of the 10-pin connection cord is
does not iight).
• The 10-pin connector is not piugged in compietely.
• The grouhding pin (black) of the 10-pin connection cord is
• The negative (-) cabie of the car battery is disconnected.
• The attenuator of the center unit is set to ON.
• The LEVEL control is set to the MIN position.
No sound
• The speaker cords are connected improperly.
• Connection terminais are connected improperly.
Sound quaiity is bad
• The LEVEL control Is set to the MAX position.
(sound is distorted).
Unable control
• Remote control cord is not connected.
• The speaker cords are connected with incorrect positive
• The grounding pin (black) of the 10-pin connection cord is
The sound Is unnatural.
• The balance between the front speakers or between those
Specifications
Cauflon:----------------------------------------------------------------------------------------
The following ratings and design are subject to change without notice.
[Amp unit]
[Speaker unit]
[Amp unit] + [Speaker unit]
8
KFC-WDA69RC
Cause
is not connected.
not connected.
not connected.
(+)/negative (-) polarity.
poorly contacted.
and the rear speakers are not well adjusted.
Type
Maximum output
Frequency Response (System)
S/N ratio
Low Pass Filter Frequency
Phase
RCA pin jack
Sensitivity/
Input Impedance
Speaker input
Power
Maximum current consumption
Fuse capacity
External size
Weight
Maximun input
Impeadance
Woofer
External size
Net weight
Remedy
•
Check the
( + ) / { - )
polarity of the power cord and that the
cords are not shorted, then replace with a fuse with the
rated capacity.
•
Re-connect the cords correctiy by referring to the connec
tion example (on page 5).
•
Connect the cord correctly by referring to the connection
example (on page 5).
•
Check the connections of all cords, then connect the (-)
cable to the battery.
• Insert the connector all the way in.
•
Attach the grounding terminal to the metallic section of thp
vehicle (not a coated surface) by tightly screwing it.
• Check the connections of all cords, then connect the (-)
cable to the battery.
• Switch the attenuator OFF.
• Increase the volume to an optimum level.
• Connect the cords correclty by referring to the connection
example (on page 5). j
• Insert the connectors or jacks air the way in to the terminals.
• Set the volume to an optimum level.
• Connect remote control cord to remote control terminal.
•
Connect the cords correctly by referring to the connection
example (on page 5).
•
Attach the grounding terminal to the metallic section of the
vehicle (hot a coated surface) by tightly screwing it.
• Adjust the top'e balance by switching the PHASE switch to
0° or 180° as required.
COMPACT POWERED SUBWOOFER
200W
30-150Hz
85dB
50Hz, 80Hz, 100Hz, 150Hz (4 steps)
0°, 180°
210mV/10kil
4.2V/Ikil
DC14.4V (Operational range 10.5 - 16V)
10A
5Ax2
Width 195mm x height 30mm x depth 155mm
(7-11/16"
1-3/16"
6-1/8")
X
X
800g (1.81b)
200W
1.5 ii
153mm
229mm Cone type
X
Width 255mm x height 184mm x depth 110.4mm
(10-1/16" X 7-1/4" X 4-3/8")
4.0kg (8.8 lb)