Pioneer RS-A99 Schnellstartanleitung

Optical Digital Reference System
BRIDGEABLE FOUR-CHANNEL POWER AMPLIFIER
Système numérique optique de référence
AMPLIFICATEUR DE PUISSANCE PONTABLE A QUATRE VOIES
Sistema ottico digitale di riferimento
AMPLIFICATORE DI POTENZA A QUATTRO CANALI COLLEGABILE A PONTE
Sistema de Referencia Digital Óptico
AMPLIFICADOR DE POTENCIA DE CUATRO CANALES EN PUENTE
Optisches Digital-Referenzsystem
BRÜCKBARER 4-KANAL-LEISTUNGSVERSTÄRKER
Optisch digitaal referentiesysteem
SCHAKELBARE 4-KANAALSVERSTERKER
Оптическая цифровая справочная система
ЧЕТЫРЕХКАНАЛЬНЫЙ УСИЛИТЕЛЬ МОЩНОСТИ С ВОЗМОЖНОСТЬЮ МОСТОВОГО ВКЛЮЧЕНИЯ
RS-A99
Quick start guide
Guide de démarrage rapide
Guida rapida all'uso
Guía de iniciación rápida
Schnellstartanleitung
Snelstartgids
Быстрый запуск проводника
Printed in Japan
Imprimé au Japon
<CRD4504-A> EW <KOKZF> <0D00000>
English
Connection diagram
Special red battery wire
RD-228 (sold separately)
Fuse (40 A) X 2
After completing all other amplifier connections, finally
Grommet connect the battery wire terminal of the amplifier to the
positive () battery terminal.
Car stereo with RCA
Ground wire (Black)
output jacks
RD-228 (sold separately)
(sold separately)
Connect to a clean,
paint-free metal location.
RS-P99
(sold separately)
External output
If only one input plug is used, do not
connect anything to RCA input jack B.
Connecting wire with RCA
pin plugs
(sold separately)
RCA input jack A
Left side
Fuse (25 A)
Right side
RCA input jack B
Speaker output terminals
Refer to "Connecting the speaker
System remote control wire (sold separately)
output terminals" in the owner's
Connect male terminal of this wire to the system remote control
manual.
terminal of the car stereo. The female terminal can be connected to
the auto-antenna relay control terminal. If the car stereo lacks a
system remote control terminal, connect the male terminal to the
power terminal via the ignition switch.
Connecting the speakers Connections when using the
RCA input jack
The speaker output mode can be four-channel,
three-channel (stereo and mono) or two-channel
Connect the car stereo RCA output jack and the
(stereo or mono). Connect the speaker leads
RCA input jack of the amplifier.
based on the mode and the figures shown below.
Four-channel / Three-channel
Four-channel output
output
Left Right
Speaker out A Slide INPUT SELECT (input select) switch to 4CH
position.
Set the LEFT CHANNEL (left channel) and RIGHT
CHANNEL (right channel) switches to the same
position.
RCA input jack A
RCA input jack B
Left Right
Speaker out B
Three-channel output
Left Right Connecting wires with
Speaker out A
RCA plugs
(sold separately)
From RS-P99 (sold separately) etc. (RCA output)
If only one input plug is used, connect the plug to
RCA input jack A rather than B.
Speaker out B (Mono)
Two-channel output (Stereo) / (Mono)
Slide INPUT SELECT (input select) switch to 2CH
Two-channel output (Stereo)
position.
Speaker (Left)
Set the LEFT CHANNEL (left channel) and RIGHT
CHANNEL (right channel) switches to the same
position.
RCA input jack A
For two-channel output,
connect the RCA plugs
to the RCA input jack A.
Speaker (Right)
Two-channel output (Mono)
Connecting wire with
Speaker (Mono)
RCA pin plugs
(sold separately)
From RS-P99 (sold separately) etc. (RCA output)
Speaker (Mono)
What's what
1
2 3 4 4 3 2
1 Power indicator 3 INPUT SELECT (input select) switch
The power indicator lights up to indicate Select 2CH for two-channel input and 4CH for
power ON. four–channel input.
2 LEVEL ADJUST (level adjustment) - Set the LEFT CHANNEL (left channel) and
RIGHT CHANNEL (right channel) switches to
control
the same position.
LEVEL ADJUST (level adjustment) control
4 SUPER HI-VOLTAGE MODE (super
helps align the input level of each channel.
high-voltage mode) switch
Both LEFT CHANNEL (left channel) and RIGHT
CHANNEL (right channel) are available for CH When connecting to RS-P99 (sold separately),
A (channel A) and CH B (channel B). turn on the SUPER HI-VOLTAGE MODE (super
To increase the level, turn LEVEL ADJUST high-voltage mode) switch.
(level adjustment) clockwise. To decrease the - Set the LEFT CHANNEL (left channel) and
level, turn LEVEL ADJUST (level adjustment) RIGHT CHANNEL (right channel) switches to
counterclockwise. the same position.
- In case of a bridge connection of speakers, - When connecting to devices other than RS-
set the speakers' LEVEL ADJUST (level P99, turn the switch to off. If you turn it on,
adjustment) switches to the same position. the volume may decrease.
- When connecting to a car stereo that outputs
high power, if you turn up the volume of the
car stereo and distortion is increased, turn
down the car stereo volume.