Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
English
Parts supplied
Adapter cable
MHL adapter × 1
Power supply box × 1
(HDMI Type A - D) × 1
HDMI cable
USB - micro USB cable
(Type A - A) × 1
(Type USB A - micro USB B) × 1
• Use only the cables included in this connectivity kit to ensure proper connection.
• Do not use the cables included in this connectivity kit for other models.
Connecting the in-vehicle product using HDMI cables
Adapter cable
HDMI cable
(HDMI Type A - D)
(Type A - A)
0.75 m (2 ft. 6 in.)
1.5 m (4 ft. 11 in.)
HDMI terminal
USB - micro USB cable
(Type USB A - micro USB B)
2.25 m (7 ft. 5 in.)
Power supply box
Fuse (2 A)
Notes:
• The positions of the HDMI terminals dif-
Red
fer depending on the in-vehicle product.
To electric terminal controlled by
For details of the terminals' positions,
ignition switch (12 V DC) ON/OFF
refer to the manual of each product.
• The MHL adapter will not be used if you
Black (ground)
use the adapter cable (HDMI Type A-D).
To vehicle (metal) body
Connecting the in-vehicle product using the MHL adapter
HDMI cable
(Type A - A)
MHL adapter
1.5 m (4 ft. 11 in.)
0.75 m (2 ft. 6 in.)
HDMI
terminal
USB - micro USB cable
(Type USB A - micro USB B)
2.25 m (7 ft. 5 in.)
Power supply box
Fuse (2 A)
Notes:
• The positions of the HDMI terminals dif-
Red
fer depending on the in-vehicle product.
To electric terminal controlled by
For details of the terminals'positions,
ignition switch (12 V DC) ON/OFF
refer to the manual of each product.
Black (ground)
• The adapter cable (HDMI Type A-D) will
To vehicle (metal) body
not be used if you use the MHL adapter.
Installing the power supply box
1 Decide on the installation position.
Notes:
• Thoroughly wipe off the surface before
Power supply box
affixing the adhesive tape.
• Use separately sold adhesive tapes
to secure this product so that it does
not move. It is extremely dangerous if
cords are exposed on the floor as they
Adhesive tape
may become entangled with the brake
(sold separately)
pedal etc. Hide cords so that they do
not get in the way when you are driv-
ing.
• Secure all wiring with cable clamps or
2 Attach the power supply box using
electrical tape. Do not allow any bare
separately sold adhesive tapes.
wiring to remain exposed.
Information to User
• This product cannot be installed in a
vehicle without ACC (accessory) posi-
tion on the ignition switch.
Alteration or modifications carried out with-
out appropriate authorization may invalidate
the user's right to operate the equipment.
If you want to dispose this product,
do not mix it with general house-
hold waste. There is a separate
ACC positi on
No ACC positi on
collection system for used elec-
Cords for this product and those for other
tronic products in accordance with
products may be different colors even if they
legislation that requires proper
have the same function. When connecting
treatment, recovery and recycling.
this product to another product, refer to the
Private households in the member states
supplied manuals of both products and con-
of the EU, in Switzerland and Norway may
nect cords that have the same function.
return their used electronic products free
of charge to designated collection facili-
• When replacing the fuse, be sure to only
ties or to a retailer (if you purchase a simi-
use a fuse of the rating prescribed on
lar new one). For countries not mentioned
this product.
above, please contact your local authori-
• This product is for vehicles with a 12-volt
ties for the correct method of disposal.
battery and negative grounding. Before
By doing so you will ensure that your dis-
installing it in a recreational vehicle,
posed product undergoes the necessary
truck, or bus, check the battery voltage.
treatment, recovery and recycling and
thus prevent potential negative effects on
• To avoid shorts in the electrical system,
the environment and human health.
be sure to disconnect the
battery
cable before beginning installation.
WARNING:
• Route and secure all wiring so it can-
Handling the cord on this product or
not touch any moving parts, such as
cords associated with accessories sold
with the product may expose you to
the gear shift, parking brake and seat
chemicals listed on proposition 65 known
rails. Do not route wiring in places that
to the State of California and other gov-
get hot, such as near the heater outlet.
ernmental entities to cause cancer and
If the insulation of the wiring melts or
birth defect or other reproductive harm.
gets torn, there is a danger of the wir-
Wash hands after handling.
ing short-circuiting to the vehicle body.
• Secure the HDMI cable using the holder
provided with your vehicle's unit.
• As the power box can heat up, it should
never be installed in the following locations:
– where it could come into contact with
car wiring or equipment
– where it would easily come into con-
tact with passengers.
Important safeguards
Specifications
Power source
This manual explains how to connect the
in-vehicle product via the connectivity kit.
........14.4 V DC (10.8 V to 15.1 V allowable)
For details of the operation of the con-
Max. current consumption ........1 A
nected product, refer to another manual.
Operation temperature range
• Read this manual fully and carefully
........–10 ºC to +60 ºC (+14 ºF to +140 ºF)
before installing this product.
Storage temperature range
• Keep this manual handy for future reference.
........–20 ºC to +80 ºC (–4 ºF to +176 ºF)
• Pay close attention to all warnings in this
manual and follow the instructions carefully.
Dimensions
• Do not install this product where it may
Power supply box (W×H×D)
(i) obstruct the driver's vision, (ii) impair
the performance of any of the vehicle's
........56 mm × 25 mm × 74 mm
operating systems of safety features,
(2-1/4 in. × 1 in. × 2-7/8 in.)
including airbags, hazard lamp but-
MHL adapter (W×H×D)
tons, or (iii) impair the driver's ability
........41 mm × 15 mm × 45 mm
to safely operate the vehicle. In some
(1-5/8 in. × 5/8 in. × 1-3/4 in.)
cases, it may not be possible to install
this product because of the vehicle type
or the shape of the vehicle interior.
Weight
• Make sure that the cables and wires
Power supply box ........120 g (0.3 lbs)
are routed and secured so they will not
MHL adapter .................50 g (0.1 lbs)
interfere with or become caught in any
of the vehicle's moving parts, especial-
Note:
ly the steering wheel, shift lever, park-
Specifications and design are subject to
ing brake, sliding seat tracks, doors, or
possible modifications without notice
any of the vehicle's controls.
due to improvements.
Werbung
Inhaltsverzeichnis
